A、 确保杆之间有合适的间隙。
B、 确保杆之间有合适的角度。
C、 确保杆之间有足够的间隙。
答案：C
A、 确保杆之间有合适的间隙。
B、 确保杆之间有合适的角度。
C、 确保杆之间有足够的间隙。
答案：C
A. 主要部件的制造商提供的维护、故障排除、检查和修理相关数据应遵守本规范的格式。但对于电源、总线系统、继电器、跳开关、开关以及特定飞机制造商和型号常用的其他部件，可视情在基本的机体维护手册中予以描述。
B. 预计主要部件的制造商将以本规范的格式提供维护、故障排除、检查和维修数据。然而，电源、总线系统、继电器、断路器、开关和其他特定品牌和型号的通用项目，将在基本机身维修手册中进行必要的显示和描述。
C. 主要部件的制造商应按本规范的格式提供维护、故障排除、检查和修理相关的资料。然而，电源、总线系统、继电器、跳开关、开关和其他一些常见的特殊构造和型号将在基本机身维护手册中显示和描述。
A. A pilot with certification authorized by Part 43 of the regulation can perform limited preventive maintenance.
B. According to Part 43 of the regulation, A pilot is certificated to perform limited preventative maintenance.
C. A certificated pilot is authorized by Part 43 of the regulation to perform limited preventive maintenance.
A. 使用符号代表电磁活门，显示该活门是否是弹簧加载到开位或关位。
B. 应针对电磁活门标明注意事项，说明该活门应该弹簧加载到开位还是关位。
C. 电磁活门应标有符号，表明该活门是弹簧加载到开位还是关位。
A. To gain entry to the nearby structure, take out the sensor.
B. Remove the sensor to get access to the adjacent structure.
C. Disassemble the sensor to get access to the adjacent structure.
A. 提高温度以缩短固化时间。
B. 提高温度以缩短治疗时间。
C. 降低温度以增加固化时间。
A. 笔记本电脑有以下主要部件
B. 笔记本电脑有以下初级部件
C. 笔记本电脑有以下仿制部件
A. During the system test, the PSU nitrogen mask doors will open and the nitrogen masks will appear in the nitrogen box if the door test stop or the tapes are not installed.
B. If the door test stop or the masking tape is not installed, the doors of the PSU oxygen box will open and the oxygen mask will remain in the original position.
C. The PSU oxygen box doors will open and the oxygen masks will go out of the oxygen boxes during the functional test if you do not install the door test stop or the masking tape.
A. Set the tensiometer to zero.
B. Empty the tension regulator.
C. Zero the tension indicator.
A. 该符号指该章节的全部或大部分规则。
B. 该索引指本部分的全部大部分规则。
C. 该内容包括那个部门的全部或大部分规则。
A. Visual difference is acceptable between the previous surface and the new surface.
B. There should be no visual difference between the initial surface finish and the new surface finish.
C. It is forbidden to have acoustic difference between the former surface finish and the new surface finish.
