A、 拧紧螺栓时使用不同的措辞。
B、 使用不同的扳手拧紧螺栓。
C、 拧螺栓时使用不同的扭矩。
答案:A
A、 拧紧螺栓时使用不同的措辞。
B、 使用不同的扳手拧紧螺栓。
C、 拧螺栓时使用不同的扭矩。
答案:A
A. 包括点火线束、高压导线、“低压”系统中使用的线圈、火花塞、点火器等。
B. 包括点火线装置、高压导线、“低压”系统中使用的线圈、点火器等。
C. 包括点火线装置、低压导线、“低压”系统中使用的线圈、火花塞、点火器等。
A. 水和甲醇的混合物增加了发动机的功率。
B. 水和乙醇的混合物增加了发动机的功率。
C. 水的混合物和丙醇增加了发动机的功率。
A. The lean fuel flow mixtures will be provided by the EGT indicators under different engine powers.
B. EGT indicators constantly monitor the lean fuel flow mixtures wherever the thrust lever is.
C. The lean fuel flow mixtures are induced by the EGT indicators to various powerplants.
A. Generally, in describing the airplane or its system, third person wording should be used. (For example: The nose wheel is provided with a shimmy damper to keep the wheel from shimmying while rolling on the ground.)
B. In general, when describing the aircraft or its system, you should use third person such as there is shimmy damper on the nose wheel in order to prevent the wheel shimmying and rolling on the ground.
C. Generally speaking, third person should be used while describing the aircraft or their system. For example: the nose wheel is available on the shimmy damper so as to shimmy or roll on the ground.
A. The aft lanyard attached to the access door to the right APU compartment is broken.
B. The after end of lanyard attached to the access door to the right APU compartment is fractured.
C. The lanyard attached to the after end of the right access door to the APU compartment is frayed.
A. State structure of airframe, wings and tail.
B. Present structure of airframe, wings and empennage.
C. Describe structure of fuselage, wings, and empennage.
A. Procedures shall be omitted for coping with cases of smoke and/or fire in the cabin or from an engine in the following flight segments.
B. Procedures shall be provided for accompany with cases of smoke and/or fire in the cabin or from an engine in the following flight sectors.
C. Procedures shall be provided for coping with cases of smoke and/or fire in the cabin or from an engine in the following flight phases.
A. Take care to the absence of leakage during the execution of each step in the valve test.
B. Throughout the valve test, verify that there are no obvious signs of leakage at each step.
C. Make certain that no leakage is present as you proceed with each step of the valve test.
A. "Maintenance Practices" include servicing, removal/installation, adjustment/test, inspection/check, cleaning/painting, and approved repairs. "Maintenance Practices" should obey the instructions of the Troubleshooting Section.
B. "Maintenance Practices" include servicing, removal/installation, adjustment/test, inspection/check, cleaning/painting, and approved repairs. "Maintenance Practices" should be located after the Troubleshooting Section.
C. "Maintenance Practices" include servicing, removal/installation, adjustment/test, inspection/check, cleaning/painting. And approved repairs should be located after the Troubleshooting Section.
A. This example shows that we were only allowed to calculate the data applicable to a Type B unit.
B. The data we are now calculating in this example apply only to Type B unit.
C. The data used for the calculations in this example apply only to a Type B unit.