A、 我们在这个产品中不使用添加剂。
B、 我们不使用附属产品。
C、 我们在此生产过程中不使用粘接剂
答案:A
A、 我们在这个产品中不使用添加剂。
B、 我们不使用附属产品。
C、 我们在此生产过程中不使用粘接剂
答案:A
A. 设备清单应包含特定飞机在交付时已安装的所有必需或选装设备。
B. 交付时,应按照设备清单在具体飞机上安装所有必要或选装设备。
C. 设备清单应包含送达时在具体飞机上安装的所有要求或选装设备。
A. 应说明总容量和可用燃料,如果不可用燃料超过FAR23的限制,在飞行中不可用数量的信息应被提供。
B. 如果不可用燃油超过FAR23的限制,则应说明总容量和可用燃油并确定提供在飞行中不可用燃油量的信息。
C. 应说明总容量和可用燃油,如果不可用燃油超过FAR23的限制,应提供确定在飞行中不可用燃油量的信息。
A. It is understood that compliance with the above can in some instances cause duplication of test procedures, which is acceptable.
B. It will lead to repeat the test process when you obey the regulations in some cases, it is barely to be accepted.
C. It is understood that follow the above regulations may cause repeating in the test procedures , although it is allowable.
A. 建议包含紧急程序为了超级充电器或涡轮充电器失效
B. 包含针对增压器/涡轮增压器失效应急程序的建议
C. 建议包含了超级涡轮或涡轮充电器失效的紧急程序
A. Apply two kindreds of protective compound to shield the sealant from any harm caused by hydraulic fluid.
B. In order to prevent damage to the sealant from hydraulic fluid, it is necessary to apply two layers of protective compound.
C. To prevent hydraulic fluid from drowning the sealant, it is recommended to apply two layers of protective compound.
A. 任何以ATA No.100格式发布的技术数据将满足本规范的要求,尽管预期在没有ATA-100要求的情况下将使用第19段格式。
B. 任何以ATA No. 100格式发布的技术数据将满足本规范的要求,但在没有预见ATA-100要求的情况下,将使用第19段格式。
C. 任何以ATA No. 100格式发布的技术数据将满足本规范的要求,但在预见不需要满足ATA-100要求的情况下,将使用第19段格式。
A. 数据应显示最大飞机重量条件下、油门关闭时,不同襟翼构型、滚转角条对应的指示空速和校正空速。
B. 数据应以指示空速和校准空速与襟翼配置和最大重量时关闭油门的坡度角来表示。
C. 数据应显示为指示空速和标定空速与襟翼配置以及节气门关闭时最大重量下的倾斜角度。
A. 指示器显示储压器已满。
B. 仪表显示油箱已满。
C. 指示器显示油箱已满。
A. The power plant refers to the overall power package, including engine, air intake, bracket, cowling, nacelle, cowl flaps, cooling baffles, etc.
B. The power plant refers to the overall power package inclusive of engine, air intake, mount, cowling, scoops, cowl flaps, cooling baffles, etc.
C. The power plant refers to the overall power package inclusive of engine, air intake, mount, cowling, nacelle caps, fairing flaps, cooling baffles, etc.
A. Sample the fluid to contaminate microbiology.
B. Do a fuel sampling for microbiological contamination.
C. Obtain a demo of oil to determine the microbial pollution.