A、 Put the end of the rod that has a screw in the fitting.
B、 Put the end of the rod that has a thread in the adapter.
C、 Put the end of the rod that has a thread in the fitting.
答案:C
A、 Put the end of the rod that has a screw in the fitting.
B、 Put the end of the rod that has a thread in the adapter.
C、 Put the end of the rod that has a thread in the fitting.
答案:C
A. 为了参考使用,标签分隔符应该按顺序排列。
B. 交错使用制表分隔符将有助于参考。
C. 为了便于参考,隔页签应交错排列。
A. This compound can eliminate poisonous fumes.
B. This compound can release poisonous fumes.
C. This composite alloy can release poisonous fumes.
A. 按照服务公告2243,所有开裂的接耳都有两个凸缘衬套安装在接耳孔中,或者在生产时解决直衬套与安定面配合U型槽失配的早期问题。
B. 根据服务公告2243或在生产中,所有出现裂纹的接耳都在接耳孔中安装了两个凸缘衬套,以消除直衬套移入到安定面的配合U型槽中的早期问题。
C. 根据服务通告2243,在生产过程中给所有出现裂纹的接耳孔中都安装了两个凸缘衬套,解决了之前直衬套游移到安定面配合U型槽的问题。
A. 如果无线电信号不清晰,重新调整频率。
B. 如果电信号没有被清除,重新调整频率。
C. 如果无线电信号没有被清除,重新调整频率。
A. 因为轴的损坏,导致泵不运转。
B. 由于泵的设计问题,导致其停止运转。
C. 泵运转失常的原因在于叶轮的损坏。
A. 用标记识别曲柄和轴,以防止安装错误。
B. 用标记识别曲柄和轴,以阻止安装错误。
C. 用标记识别手柄和轴承,以防止安装错误。
A. 如果没有明显迹象表明紧固件松动,在紧固件头部和相邻材料上标记一条红线。
B. 如果紧固件松动的迹象不清晰,则跨过紧固件头部在相邻材料上标记一条红线。
C. 如果没有清晰地显示出紧固件松动,则在紧固件头部和相邻材料的上方标记一条红线。
A. Make sure that you can see the oil level through the sight gauge.
B. Make sure that the oil quantity is shown on the oil level indicator.
C. You can read the oil level on the oil level gauge.
A. “修理/改装”用于描述修理或改装说明,也可指向其他文件中的标准修理或其他地方定义的特殊修理或改装,如在服务包、服务通告等中。
B. “修理/改装”用于描述修理或改装指令,也可指向其他文件中的标准修理或其他文件(如服务包或服务通告等)中界定的特殊修理或改装。
C. “修理/改装”用于描述维修或改装说明,可能指另一份文件中的标准维修或其他地方定义的特殊维修或改装,如维修包、维修公告等。
A. The actuator receives a hydraulically controlled mechanical command from FCC who sends an electrical commands and the aileron and the elevator power control units(PCU) will carry out this command.
B. FCC sends an electrical order to autopilot actuator. The actuator converts it to a hydraulically controlled mechanical command. The aileron and the elevator power control units(PCU) will carry out this command.
C. FCC sends an electrical commands to autopilot actuator. The actuator receive it to a hydraulically controlled unit . The aileron and the elevator power control units(PCU) will carry out this command from hydraulically controlled unit.