A、 如有必要进一步减小钢索张力,可使用松紧螺套。
B、 如有必要进一步降低钢索张力,可使用张力计。
C、 如有必要进一步调节钢索长度,可使用旋转带子。
答案:A
A、 如有必要进一步减小钢索张力,可使用松紧螺套。
B、 如有必要进一步降低钢索张力,可使用张力计。
C、 如有必要进一步调节钢索长度,可使用旋转带子。
答案:A
A. 本程序给出了用于水管临时修理的两种方法。
B. 本程序给出了水管的永久修理方法。
C. 本程序详细阐述了两种方法来解决水管的修理。
A. 装配之前,确保适当减少减震器里的压力。
B. 拆卸之前,确保释放减震器里的初始压力。
C. 分解之前,确保减震器里的所有氮气压力已释放。
A. 如果其他地方提供了信息,则改版记录是可选的。
B. 如果其他地方提供了信息,则改版记录是必选的。
C. 如果其他地方提供了信息,则改版记录是过期的。
A. 维修破损的泵。
B. 拆卸相应的泵。
C. 更换故障泵。
A. There are some environmental reasons of the manufacturers or operators such as the location of battery compartments.
B. Some environmental factors are within the control of the manufacturer or the operator such as the location of battery compartments.
C. It is the manufacturer or the operator's environmental factors, such as the location of the battery compartments.
A. 风挡出口是在机长和副驾的挡风口前面。
B. 风挡出口是在机长和副驾遮光板的前面。
C. 风挡出口是在机长和副驾操作板的前面。
A. Crucial angle of attack is the angle at which a stream or air flow begins to split from a surface,causing a decrease in efficiency. It is important for designing dynamic surfaces ,such as airplane wings,turbine blades,as it determines the maximum attack angle that can be achieved without causing loss of lift or thrust.
B. Crutial angle of attack is the angle at which a stream or air flow begins to seperate from a surface,causing a decrease in efficiency. It is important for designing aerodynamic surfaces ,such as airplane airfoils,turbine blades,as it determines the maximum attack angle that can be achieved without causing loss of lift or thrust.
C. Critical angle of attack is the angle at which a fluid or air flow begins to separate from a surface, causing a reduction in the efficiency of the flow. The critical attack angle is an important consideration in the design of aerodynamic surfaces, such as airplane wings, turbine blades, as it determines the maximum angle of attack that can be achieved without causing a loss of lift or propulsion.
A. If the valve is the source of the fuel leak, discard the valve seals and install new ones.
B. If the fuel leaks out of the valve, reinstall the valve seals.
C. If the fuel leak flows towards the valve, discard the valve seals and install new ones.
A. In this Section which is a separate attachment of the Handbook or as a separate document, the manufacturer shall provide an equipment list.
B. The manufacturer shall provide an equipment list in this Section, in a separate document appended to the Handbook, or as a separate document.
C. Being a separate appendix of the Handbook or as a separate document, the manufacturer shall provide a list of equipment of this Section.
A. 凹坑没有伤及保护漆层。
B. 划痕没有穿透保护层。
C. 划痕没有贯穿保护膜。