A、 Detach the sensor to establish a physical connection with the adjoining structure.
B、 Install the sensor to block access to the adjacent structure.
C、 Take out the sensor to reach to the neighboring structure.
答案：C
A、 Detach the sensor to establish a physical connection with the adjoining structure.
B、 Install the sensor to block access to the adjacent structure.
C、 Take out the sensor to reach to the neighboring structure.
答案：C
A. 在飞机座舱增压系统部分，应描述如何识别潜在问题和处理紧急情况。
B. 在飞机座舱增压系统部分，应说明识别可能问题和处理障碍的方法。
C. 在飞机座舱增压系统部分，说明识别问题和处理紧急情况的方法。
A. 螺柱的凹陷不得超过5mm。
B. 螺柱的突起不得超过5mm。
C. 螺纹的长度不得超过5mm。
A. 拧紧螺栓时使用不同的措辞。
B. 使用不同的扳手拧紧螺栓。
C. 拧螺栓时使用不同的扭矩。
A. At the location shown in the figure, waterproof corrosion inhibiting compound has been used on certain aircraft construction. To keep the effectiveness of this protection, reapply the compound in these or other locations periodically.
B. Water displaying corrosion inhibiting compound has applied on certain airplanes structure in the locations in this figure. Periodic reapplication must be applied in these and other locations, so as to maintain effectiveness of this protection.
C. Water displacing anti-seize compound has been applied on certain airplanes construction in the locations in this figure. Periodic reapplication should be utilized in these and other locations, in order to keep effectiveness of the protection.
A. Turn the adjuster clockwise to increase 60 Deg.
B. Turn the adjuster counterclockwise in increments of 60 Deg.
C. Decrease 60 Deg. to turn the adjuster counterclockwise.
A. 辅助结构包括前缘、后缘、翼尖、翼尖油箱和燃油或水单元隔板，不包括镀层/蒙皮。
B. 辅助结构包括前缘、后缘、翼尖、翼尖油箱和燃料或水电池背板，不包括板/皮。
C. 辅助结构包括前缘、后缘、翼尖、尖端燃料箱和燃料或水电池背板，不包括板/蒙皮。
A. After flight test, customer will paint aircraft.
B. The aircraft which has been painted will fly to customer after flight test .
C. We will paint aircraft for customer after flight test.
A. Each manufacturer is expected to reasonably abide by the Specification content and arrangement.
B. Each manufacturer is expected to reasonably agree with the Specification content and arrangement.
C. Each manufacturer is expected to reasonably substitute the Specification content and arrangement.
A. 格式和排版由CAP编写者决定，要认识到其格式和排版最好与编写者现有文件相似。
B. 格式和排版由CAP生产者提议，其批准需经过与现有文件格式和排版的对比。
C. 格式和排版由CAP生产者定义，并预期与现有的文件格式和排版保持一致。
A. Clean all lint, dust and debris from the ventilation holes located on the aft side of the captain＇s primary flight, navigation, and center lower engine display units.
B. Clean the vent holes behind the captain＇s primary flight, navigation and lower middle engine display units which are blocked by lint, dust and debris.
C. The captain＇s primary flight, navigation, and center lower engine display units must be cleaned since the ventilation holes behind them are clogged by lint, dust and debris.
