A、 If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
答案:B
A、 If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
答案:B
A. Make sure that there are no foreign particles in the oil.
B. Make sure that there are no metal particles in the oil.
C. Make sure that there are exempt metal particles in the oil.
A. This commonality requires greater learning and understanding for pilots, aircraft maintenance technicians and engineers alike.
B. This commonality makes it easier for pilots, aircraft maintenance technicians and engineers alike to learn and understand.
C. This commonality brings about better learning and understanding of the pilots, aircraft maintenance technicians and engineers alike.
A. Set the air conditioning switch to the up position.
B. Place an air conditioning switch above the normal position.
C. Put one of the pack switches in the HIGH position.
A. Notes emphasize conditions such as operating procedures, inspection, repair or maintenance, etc., which may be met as appropriate.
B. Notes emphasize the conditions of operation procedure, inspection, repair or maintenance, etc., must be followed.
C. Conditions for operating procedures, inspection, repair or maintenance, etc. must be emphasized in the notes.
A. 乘客座位所在区域以及自助餐/厨房、卫生间、休息室和更衣室中的照明子系统。包括直接和间接照明、主警示灯系统、警示灯调光系统等。
B. 乘客座位所在区域以及自助餐/厨房、卫生间、休息室和更衣室中的照明子系统。包括直接和间接照明、乘客阅读灯、机舱圆顶灯等。
C. 乘客座位所在区域以及自助餐/厨房、盥洗室、休息室和衣帽间中的照明子系统。包括直接和间接照明、乘客呼叫系统、照明标志等。
A. 当你拆下罩环时,小心不要损坏法兰组件。
B. 当你拆下冠环扇形件时,小心不要造成法兰盘损坏。
C. 拆下法兰盘时,小心不要造成冠环扇形件损坏。
A. 如果滑油渗漏超过5滴,每分钟检测密封胶。
B. 如果滑油渗漏超过每分钟5滴,检查密封胶。
C. 如果燃油渗漏超过每分钟5滴,更换密封胶。
A. NOTE: The manufacturer may have the option of including wiring schematic in Chapter 24, Chapter 91, or establish a separate Wiring Diagram Manual.
B. NOTE: The manufacturer may have the option of including wiring schematic in Chapter 24, Chapter 91, or establish a separate Wiring Schematic Manual.
C. NOTE: The manufacturer may have the option of including wiring diagrams in Chapter 24, Chapter 91, or establish a separate Wiring Diagram Manual.
A. Turn off all the unnecessary systems.
B. Disconnect all the systems which are not necessary for the test.
C. Disconnect all testing systems as necessary.
A. 在充气活门上的防尘螺帽被拆下来了,这样新鲜的空气源才能被连接到气门杆和螺套上,以打开充气阀门。
B. 在充气阀门上的可调节螺帽被拆除了,这样新鲜的空气源才能被连接到气门杆和螺套上,以打开充气阀门。
C. 充气阀门上的防尘帽被拆除,外接气源连接到阀门杆,旋转螺母被旋开以打开充气阀门。