A、 Turn the drain valve counterclockwise to cause the fluid to stop flowing before the valve is pushed.
B、 When you turn the drain valve counterclockwise, no fluid will flow until you push the valve in.
C、 Make sure there is no fluid flowing after the valve is pushed, then turn the drain valve clockwise.
答案:B
A、 Turn the drain valve counterclockwise to cause the fluid to stop flowing before the valve is pushed.
B、 When you turn the drain valve counterclockwise, no fluid will flow until you push the valve in.
C、 Make sure there is no fluid flowing after the valve is pushed, then turn the drain valve clockwise.
答案:B
A. 如果RAT被撤回,缓慢并完全将其伸出,确保与其他部件衔接上。
B. 如果追踪到RAT,则缓慢并完全释放RAT,确保信号不与其他混淆。
C. 如果RAT是收回状态,缓慢和完全展开RAT,并确保它不碰到其他部件。
A. 在工作区入口处设置安全屏障。
B. 在工作区域放置安全电源。
C. 放置安全屏障在入口通道的位置。
A. 如果杆被意外移动,请跳过测试。
B. 如果手柄意外移动,再做一次测试。
C. 如果重新测试,确保手柄不会意外移动。
A. 两个电感器在后锁连杆上方工作。
B. 两个传感器位于后锁连杆的顶部。
C. 两个探测器在杆锁定位的后上方。
A. 在铝合金部件上不要使用藏红花布,它含有氧化铁,在铝合金部件上会造成划痕。
B. 在铝质部件上不要使用细砂布,细砂布含有氧化铁,在铝质部件上会造成腐蚀。
C. 在铝合金部件上不要使用细砂布,细砂布含有氧化铁,在铝合金部件上会造成腐蚀。
A. This procedure is only applicable to type A parts.
B. This task is only used for type A parts.
C. This procedure is applicable to all type parts.
A. The needle moves horizontally along the gage.
B. The pointer moves vertically along the scale.
C. The indicator moves longitudinally along the edge.
A. RESET测试电门用于减少故障历史。当VERFIY(通过)和绿色GO灯亮时, 按下RESET(复位)电门。
B. RESET测试电门用于转移故障记录。当VERFIY(验证)和绿色GO灯打开时, 按下RESET(复位)电门。
C. RESET测试电门用于消除故障记录。当VERFIY(确认)和绿色GO灯亮时, 按下RESET(复位)电门。
A. 使用“降低”更好,因为它描述的是压力,而不是控制压力的指示器 。
B. 使用“降低”更好,因为它描述的是压力,而不是监测压力的指示器。
C. 使用“增加”更好,因为它描述的是压力,而不是监测压力的指示器。
A. However, manufacturers may omit System/Chapters that are not applicable to the product or combine Systems/Chapters where it is feasible.
B. However, manufacturers may adopt Systems/Chapters that are not applicable to the product or constitute Systems/Chapters when necessary.
C. However, operators may omit Systems/Chapters applicable to the product or constitute Systems/Chapters where practical.