A、 飞机审定条件包括:一台发动机不工作并处于风车状态(或对于安装自动顺桨装置的飞机,已顺桨),朝向工作发动机一侧倾斜不超过5度,工作发动机处于起飞功率,起落架收上,襟翼在起飞位置,以及最临界重心位置。
B、 飞机的审定条件包括:一个发动机停车,有风动(或在有自动羽化装置的飞机上,已羽化)朝向工作发动机的倾斜度小于5度,起落架升起,襟翼处于起飞状态,以及最不利的重量。
C、 飞机的审定条件包括:一个发动机停止工作,有风动(已在飞机上调为自动顺桨模式)朝向工作发动机的倾斜度大于5度,起落架升起,襟翼处于起飞状态,以及重心处于临界位置。
答案:A
A、 飞机审定条件包括:一台发动机不工作并处于风车状态(或对于安装自动顺桨装置的飞机,已顺桨),朝向工作发动机一侧倾斜不超过5度,工作发动机处于起飞功率,起落架收上,襟翼在起飞位置,以及最临界重心位置。
B、 飞机的审定条件包括:一个发动机停车,有风动(或在有自动羽化装置的飞机上,已羽化)朝向工作发动机的倾斜度小于5度,起落架升起,襟翼处于起飞状态,以及最不利的重量。
C、 飞机的审定条件包括:一个发动机停止工作,有风动(已在飞机上调为自动顺桨模式)朝向工作发动机的倾斜度大于5度,起落架升起,襟翼处于起飞状态,以及重心处于临界位置。
答案:A
A. The job is required to be divided into logical steps or operations.
B. This needs to break the work and distribute the logical steps or operations.
C. This requires to destroy the job logically into steps or operations.
A. “细节要求”部分给特殊材质的物品进行整理和排序提供特定方法。
B. “具体要求”部分描述了特殊材料的实体的一致性布局和辨别的方法。
C. “详细要求”部分提供了编排和标识特定主题材料的统一方法。
A. Review the failures report from the logbook and related fault messages with center DU or CDU, debrief the flight crew for faults and report them for handling.
B. Either the logbook or center DU/CDU shall be checked for faults records and related fault information, then review the faults reported by the flight crew and take actions.
C. Consult the failures report from the logbook to find the related information on center DU or CDU, listen to the crew for faults report. Report faults and handle them.
A. 用专用尺子确定凹坑的长度。
B. 用直尺和塞尺测量凹坑的深度。
C. 用角尺和直尺测量裂纹的深度。
A. If the pressure is above the limits, pressurize the accumulator of the door damper.
B. If the pressure is not in the given limits, pressure the cylinder of the door damper.
C. If the pressure is not in the given limits, pressurize the accumulator of the door damper.
A. The gears will automatically engage if a malfunction occurs.
B. If there is proper functioning, the gears will automatically engage.
C. If there is a malfunction, the gears will automatically disengage.
A. 确保商标完全和表面相连,没有倾斜。
B. 确保标签完全贴在表面上,没有气泡。
C. 确保标记完全附加到表面上,没有凸起。
A. 用干净的棉布浸湿水后清除除污剂。
B. 用清水浸湿并清洗带有洗涤剂的干净棉布。
C. 用干净的棉布清除污渍,再用清水洗涤。
A. 如果发现铜颗粒, 在发现之日起的30天内重复执行整个程序(机轮不承重)。
B. 如果发现金属碎屑,从即日起在30天内完成整个修理程序(机轮承重)。
C. 如果发现琥珀色指示参数,针对发现的数据在30天内重复所有程序(机轮离地)。
A. 如果温度降到零度,开启排放水系统。
B. 如果温度下降到低于零,请拆卸水系统。
C. 如果温度降至零度以下,则将水系统排空。