A、 The pressure transducer has an electrical connector that connects it to the Fuel Mnagement System.
B、 The pressure transducer connects it to the Fuel Mnagement System via electrical wire.
C、 The pressure sensor has an electronical connector that connects it to the Fuel Mnagement System.
答案：A
A、 The pressure transducer has an electrical connector that connects it to the Fuel Mnagement System.
B、 The pressure transducer connects it to the Fuel Mnagement System via electrical wire.
C、 The pressure sensor has an electronical connector that connects it to the Fuel Mnagement System.
答案：A
A. 示例应阐述最常见的情况，避免涉及标准温度、基准重量、零风速、精确参数值或其他非典型的实际情况。
B. 说明最普遍使用的情况，避免涉及标准温度、参考重量、零风速、表格精确值或其他非典型实际情况的特殊情况。
C. 说明演示的最一般用途，避免出现涉及标准温度、参考重量、零风速、表格精确条目或其他非典型实际情况的特殊情况。
A. The properties of these sealants prevent corrosion.
B. Corrosion frequently occurs due to the features of these sealants.
C. The properties of these sealants make themselves easily corroded.
A. 在一块不需要承力的金属上，可以在某一点处切割一个直径为几英寸的孔，孔的周围用法兰连接，使其具有刚度。
B. 在一块金属上，可以在不需要承力的某一点处切割一个直径为数英寸的孔，孔的边缘折边可以使其具有刚性。
C. 在一块不需要承力的金属上，可以在一处切割几个直径为数英寸的孔，孔的边缘用凸缘连接，使其产生刚性。
A. 变更表格的发起者通常会通知相关的STEMG来进行评估和表决。
B. 变更表格的发起者通常会被通知相关的STEMG评估和决定。
C. 相关的STEMG评估和决定会告知发起者表格进行了变更。
A. You can get the corrected velocity by dividing the aircraft velocity by the crosswind component.
B. Divide the crosswind component by the aircraft speed to get the correction.
C. Divide the aircraft speed by the crosswind component to get the correction.
A. Clamps should be spaced at intervals not exceeding 24 inches. Clamps on wire bundles should be selected so that they have a snug fit without pinching wires.
B. Pins should be spaced at intervals not exceeding 24 inches. Pins on harness should be selected so that they have a snug fit without pinching wires.
C. Pins should be spaced at intervals not exceeding 24 inches. Pins on harness should be selected so that they have a snug fit without scratching wires.
A. 生产商编写的维修手册必须参考本规范中包含的所有材料的格式、字体和展示方法。
B. 本手册中包含的规范可以指导厂家编写维修手册，包括所有规章书写格式和展示方法。
C. 本规范中包含的规则应作为制造商编写的维修手册中包含的所有材料的格式、样式和展示方法的指南。
A. It is important that the correct sequence of assembly is used when doing a repair, this will make sure that all parts are correctly aligned.
B. It is important to assemble the parts in a correct order during a repair which makes sure all parts correctly aligned.
C. When doing a repair, the correct sequence of assembly is important, which will make sure that all parts are correctly engaged.
A. 如果你不能脱开杆的位置，新杆的长度很可能需要调节。
B. 如果你不能断开杆和活塞，可能量错了新杆的长度。
C. 如果你不能接合杆和活塞，新杆的长度可能是不正确的。
A. 该速度指示仪此段弧线的上限是需襟翼放下时必须达到的最大速度。
B. 该速度指示仪此段弧线的上限是允许放襟翼的最大速度。
C. 该速度指示仪此段弧线的上限是襟翼收起情况下所允许的最大速度。
