68.在主轴( )调速范围内选一转速,调整切削用量,使达到设计规定的最大转矩。
A. 恒转矩
B. 恒功率
C. 恒电流
D. 恒电流
https://www.shititong.cn/cha-kan/shiti/000144a1-eef3-30f9-c061-dd2ed03feb00.html
点击查看答案
656.( )数控机床的几何精度检验包括回转轴原点的复归精度。
https://www.shititong.cn/cha-kan/shiti/000144a1-eef7-f015-c061-dd2ed03feb00.html
点击查看答案
306.F-40MR可编程序控制器,表示F系列( )。
A. 基本单元
B. 扩展单元
C. 单元类型
D. 输出类型
https://www.shititong.cn/cha-kan/shiti/000144a1-eef5-229a-c061-dd2ed03feb00.html
点击查看答案
239.( )单元是实现各种功能的核心。
A. 数控
B. 步进伺服驱动
C. 减速步进电动机
D. 控制
https://www.shititong.cn/cha-kan/shiti/000144a1-eef4-92c7-c061-dd2ed03feb00.html
点击查看答案
4.采用电压上升率du/dt限制办法后,电压上升率与桥臂交流电压( )成正比的作用。
A. 有效值
B. 平均值
C. 峰值
D. 瞬时值
https://www.shititong.cn/cha-kan/shiti/000144a1-eef2-410d-c061-dd2ed03feb00.html
点击查看答案
348.在一定电源电压Ea作用下,当负载等效电阻Rˊ相对于Ri较小时,振荡电路上交流电压Uˊ就较小,这种状态称为( )。
A. 过压状态
B. 欠压状态
C. 临界状态
D. 过零状态
https://www.shititong.cn/cha-kan/shiti/000144a1-eef5-7821-c061-dd2ed03feb00.html
点击查看答案
71.为使振荡管真空度保持正常,可以将备用管子定期在设备上轮换使用。经验证明,每隔( )个月轮换使用一次管子,对于延长其工作寿命是有益的。
A. 一、二
B. 三、四
C. 四、五
D. 五、六
https://www.shititong.cn/cha-kan/shiti/000144a1-eef3-37c7-c061-dd2ed03feb00.html
点击查看答案
354.正常时每个输出端口对应的指示灯应随该端口有输出或无输出而亮或熄。否则就是有故障。其原因可能是( )。
A. 输出元件短路
B. 开路
C. 烧毁
D. 以上都是
https://www.shititong.cn/cha-kan/shiti/000144a1-eef5-8441-c061-dd2ed03feb00.html
点击查看答案
228.市场经济条件下,不符合爱岗敬业要求的是( )的观念。
A. 树立职业理想
B. 强化职业责任
C. 干一行爱一行
D. 多转行多受锻炼
https://www.shititong.cn/cha-kan/shiti/000144a1-eef4-7cde-c061-dd2ed03feb00.html
点击查看答案
84.RS触发器特性方程是( )。
https://www.shititong.cn/cha-kan/shiti/000144a1-eef3-5133-c061-dd2ed03feb00.html
点击查看答案