A、 Solenoid valves shall be shown with a notation. The notation indicates the spring is loaded by the valve to the open or closed position.
B、 Solenoid valves shall be shown with a symbol. The valve indicates whether the valve is spring-loaded to the open or closed position.
C、 Solenoid valves shall be shown with a mark. The mark indicates whether the valve is spring-loaded to the open or closed position.
答案:C
A、 Solenoid valves shall be shown with a notation. The notation indicates the spring is loaded by the valve to the open or closed position.
B、 Solenoid valves shall be shown with a symbol. The valve indicates whether the valve is spring-loaded to the open or closed position.
C、 Solenoid valves shall be shown with a mark. The mark indicates whether the valve is spring-loaded to the open or closed position.
答案:C
A. Even though this specification is conformed to recognized industry practices , it is prepared in broad genuine terms and it is recognized that problems will occur which are not handled enough by the specification.
B. Although this specification coheres with recognized industry practices , it is written in vast general terms and it is asserted that problems will appear which are not treated sufficiently by the specification.
C. Though this specification complies with accepted industry practice, it is compiled in wide generic terms and it is recognized that problems which are not treated adequately by the specification will arise.
A. This section of the pilot's manual should clearly and confusedly provide recommended procedures for conducting normal operations.
B. The recommended procedures for conducting normal operations shall be described in this Section of the Pilot's Operating Handbook clearly and accurately.
C. The recommended procedures shall be stated in this Section of the Pilot's Operating Handbook clearly and fuzzily for the conduct of normal operations.
A. Make the panel display a warning notice in order to reveal the operation of the controls.
B. Tag a warning notice on the panel to remind the operation of the controls.
C. Put a warning notice on the panel to prevent operation of the control.
A. They comprise the three parts as follows:tail assembly,the structures at the rear of the airplane ,structures forming part of and attached to the wing.
B. They include three parts,one of them is tail assembly,one of them is the structures part at the rear of the airplane,one of them is structures part that forming part of and attached to the wing.
C. They include two parts,one of them is tail assembly at the rear of the airplane that serve to control and maneuver the aircraft,another of them is structures part that forming part of and attached to the wing.
A. By using the basic provisions of FAR 21.50, revisions become consistent with the format of the specification.
B. FAR 21.50 provisions are the basic to the revisions which are consistent with the format of the specification.
C. To make revisions consistent with the format of the specification, the provisions of FAR 21.50 should be adopted as a basis.
A. This procedure is only void in digital mode.
B. This procedure is only valid in digital mode.
C. This procedure is only ineffective in digital mode.
A. Retesting and reviewing test results are optional due to discrepancies in the fuel/water sample and the ability of the detection kits to continuously measure the level of microbial growth.
B. It is very important to do the test again and confirm test results because of differences in the fuel/water sample and the ability of the detection kits to continuously measure the level of microbial growth.
C. It is mandatory to retest and evaluate test results to make sure the differences in the fuel/water sample and the ability of the detection kits to witness the level of microbial growth.
A. Acquire the flight data from the recorder.
B. Eliminate the tape about the information after flight.
C. Remove a recording of flight data from the tape.
A. If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B. Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C. Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
A. If you use cleaner in a closed space, make sure that there is ventilation in the work area.
B. Ensure that there is adequate airflow in the work area when using solvent in an enclosed space.
C. If you use solvent in a confined space, make sure that there is restricted airflow in the work area.