A、 If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
答案：B
A、 If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C、 Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
答案：B
A. The aircrft is taxiing to China on the runway.
B. The aircrft is running to China on the ramp.
C. A Chinese aircrft is taxiing on the runway.
A. Each manufacturer is expected to reasonably abide by the Specification content and arrangement.
B. Each manufacturer is expected to reasonably agree with the Specification content and arrangement.
C. Each manufacturer is expected to reasonably substitute the Specification content and arrangement.
A. Using either method, the item to be checked is in the list of the desired condition.
B. Either way, check the listed item whose desired condition is stated.
C. No matter which method is used, the item to be checked is listed and its desired condition is presented.
A. As the depressurization of the alternate system, the hydraulic system A must be released to open the rudder hydraulic system selector valve and permit hydraulic fluid to flow to the rudder actuator below.
B. In order to depressurize standby system, the hydraulic system A must be depressurized to open the rudder hydraulic system selector valve and let hydraulic fluid flow to the lower rudder actuator.
C. Due to the depressurization of the alternate system, the hydraulic system A must be released to open the rudder hydraulic system selector valve and permit hydraulic fluid to flow to the bottom rudder actuator.
A. The repair limits are not permitted as special equipment is required.
B. The repair limits are not mentioned as special equipment is required.
C. The repair limits are not set as special equipment is required.
A. This document and the applicable airplane maintenance manual(s) complement each other.
B. This document may supplement the aircraft maintenance manual(s) as appropriate.
C. This document is explanation to the airplane maintenance manual(s).
A. By using the basic provisions of FAR 21.50, revisions become consistent with the format of the specification.
B. FAR 21.50 provisions are the basic to the revisions which are consistent with the format of the specification.
C. To make revisions consistent with the format of the specification, the provisions of FAR 21.50 should be adopted as a basis.
A. During inspection, if the nuts and washers are removed, recheck them.
B. Take a good place for the nuts and washers removed during inspection.
C. If nuts and washers are removed during inspection, install the new ones.
解析：这道题是关于在检查过程中如果螺母和垫圈被移除应该怎么处理的问题。正确答案是C:如果在检查过程中螺母和垫圈被移除，应该安装新的螺母和垫圈。
举个生动的例子来帮助理解这个知识点：假设你正在检查一台机器，发现其中的螺母和垫圈已经磨损或者损坏了，这时候就需要将它们移除并安装新的螺母和垫圈。因为螺母和垫圈在机器中起着固定和缓冲的作用，如果它们磨损或者损坏了，就需要及时更换，以确保机器的正常运转和安全性。
A. Pilots have more opportunity to move stabilizer to nose up position during takeoff thanks to the mach trim actuator who commands elevator to a more nose down position.
B. During takeoff, pilots have more opportunity to move elevator to nose up position thanks to the mach trim actuator who commands stabilizer to a more nose down position.
C. During takeoff, pilots have more opportunity to move elevator to nose down position thanks to the mach trim actuator who commands stabilizer to a more nose up position.
A. Check all parts with clear defects in accordance with standard industry practices.
B. Check all parts for visible defects in accordance with standard industry practices.
C. Check all parts for serious defects in accordance with standard industry practices.
