A、 The schematic diagrams need to list a lot of instructions, so the items listed are ordered according to certain rules, this is the order in which the items are placed on the plane.
B、 There are schematics which need to list a lot of items, so the items listed should be sorted according to certain rules, such as the order in which the items are placed on the plane.
C、 List a large number of schematics in logical order, such as the position of the items on the plane.
答案：B
A、 The schematic diagrams need to list a lot of instructions, so the items listed are ordered according to certain rules, this is the order in which the items are placed on the plane.
B、 There are schematics which need to list a lot of items, so the items listed should be sorted according to certain rules, such as the order in which the items are placed on the plane.
C、 List a large number of schematics in logical order, such as the position of the items on the plane.
答案：B
A. Choose the hydraulic system you will apply pressure.
B. Pressurize the selected hydraulic system.
C. Choose the hydraulic system you will depressurize.
A. The flap angles can not be found in Table 1.
B. The flap angles are stated in Table 1.
C. In Table 1, there are no flap angles.
A. According to the "GAMA Specification No.1", compile the Pilots Operating Handbooks.
B. Prepare Pilots Operating Handbooks through "GAMA Specification No.1".
C. Edit "GAMA Specification No.1", in accordance with Pilots Operating Handbooks.
A. If the clearance dimension is not accurate, adjust the clearance dimension between the extend proximity sensor [44A] and the target [45]. Some of the ducts in the air distribution system are wrapped with insulation material.
B. Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material .
C. Adjust the clearance dimension between the extend proximity sensor [44A] and the target [45] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
A. The airworthiness problem needs to be resolved by the way any other airplane does in the operator＇s fleet has equal or more damaging corrosion, and it has to be done before the regular check of that zone.
B. The airworthiness problem needs immediate action ahead of the next planning inspection of that zone, because it would probably occur on another plane in the operator＇s fleet, causing equivalent or more serious corrosion.
C. Due to any other airplane in the operator＇s fleet could have the comparable or more vital corrosion, the airworthiness problem should be investigated immediately before the next periodic inspection of that zone.
A. Utilize an oil-free solution.
B. Use a solution with oil.
C. The oil is not used that contains a solution.
A. This example shows that we were only allowed to calculate the data applicable to a Type B unit.
B. The data we are now calculating in this example apply only to Type B unit.
C. The data used for the calculations in this example apply only to a Type B unit.
A. Move the IDG forward and outboard until it is away from the accessory gearbox, QAD ring and power plant.
B. Move the IDG towards the forward position until the input shaft is away from the accessary gearbox and QAD ring, then move the IDG towards outboard and free of the power plant.
C. After moving the IDG towards the forward position, then it is free of the accessary gearbox, QAD and the power plant.
A. The lean fuel flow mixtures will be provided by the EGT indicators under different engine powers.
B. EGT indicators constantly monitor the lean fuel flow mixtures wherever the thrust lever is.
C. The lean fuel flow mixtures are induced by the EGT indicators to various powerplants.
A. If the lamp is too weak, charge the battery.
B. If the light is too strong, do a replacement of the battery.
C. If the light is not bright, the battery should be replaced.
