A、 查找损伤。
B、 看一下损伤。
C、 检查损伤。
答案:A
A、 查找损伤。
B、 看一下损伤。
C、 检查损伤。
答案:A
A. The lean fuel flow mixtures will be provided by the EGT indicators under different engine powers.
B. EGT indicators constantly monitor the lean fuel flow mixtures wherever the thrust lever is.
C. The lean fuel flow mixtures are induced by the EGT indicators to various powerplants.
A. These tests should only use the equipment or facilities installed on the aircraft.These tests should be able to perform by the flight crews.
B. These tests should not use the special equipment or facilities that are not installed on the aircraft.These tests should be similar to the tests performed by the flight crews.
C. These tests should require the equipment or facilities installed on the aircraft rather than the special ones and should be replaceable by the tests accomplished by the flight crews.
A. 确保通过管路的流体没有气泡。
B. 确保通过管路的油液没有杂质。
C. 确保液压油流经管路没有阻碍。
A. Ensure that you do activate the control adjacent to it.
B. Adjust the adjacent control for optimal results.
C. Make sure that you do not operate the adjacent control.
A. Rapidly and fully retract Ram Air Turbine and make sure that it doesn't attach to other parts.
B. Slowly and fully extend Ram Air Turbine and make sure that it doesn't touch other parts.
C. Make sure that the Ram Air Turbine is completely opened and it doesn't touch the other unit.
A. 拆下法兰上的四个螺钉。
B. 拆下连接法兰到活门的四个螺帽。
C. 拆下连接法兰到阀盖上的四个螺丝。
A. “功能测试:该过程旨在确定系统或组件按照最低可接受设计标准在所有方面的功能。这些测试可能需要补充地面支持设备,并且应该比飞行测试更具体和详细。它应该包含所有熟练检查所必要的信息,以维持系统或组件在可接受水平上的可靠性,无需参考其他文件。
B. “功能测试:该过程旨在确定系统或组件按照最低可接受设计标准在所有方面运行正常。这些测试可能需要补充地面支持设备,并且应该比操作测试更具体和详细。它应该包含所有熟练检查所必要的信息,以维持系统或组件在可接受水平上的可靠性,无需参考其他文件。
C. “功能测试:该过程旨在确定系统或组件按照可接受的最少系统和可接受的最低设计标准在所有方面的功能。这些测试可能需要补充地面支持设备,并且应该比飞行测试更具体和详细。它应该包含所有熟练检查所必要的信息,以维持系统或组件在可接受水平上的可靠性,无需参考其他文件。
D. B.“功能测试:该过程旨在确定系统或组件按照最低可接受设计标准在所有方面运行正常。这些测试可能需要补充地面支持设备,并且应该比操作测试更具体和详细。它应该包含所有熟练检查所必要的信息,以维持系统或组件在可接受水平上的可靠性,无需参考其他文件。
E. C.“功能测试:该过程旨在确定系统或组件按照可接受的最少系统和可接受的最低设计标准在所有方面的功能。这些测试可能需要补充地面支持设备,并且应该比飞行测试更具体和详细。它应该包含所有熟练检查所必要的信息,以维持系统或组件在可接受水平上的可靠性,无需参考其他文件。
A. 螺旋桨恒速机构故障。
B. 螺旋桨恒速机构被挡住了。
C. 螺旋桨恒速传动机构不在这个位置。
A. 表格遵循以下显示的数据。
B. 以下表格显示该数据。
C. 后面的桌子上放着数据。
A. 使用力矩扳手间隔拧紧螺栓。
B. 使用扭力扳手按顺序拧紧螺栓。
C. 使用扭矩扳手逐步拧紧螺栓。