A、 Accumulate the thickness of the shim as follows: t=x-y.
B、 Calculate the thickness of the shim as follows: t=x-y.
C、 Calculate the width of the shim as follows: t=x-y.
答案:B
A、 Accumulate the thickness of the shim as follows: t=x-y.
B、 Calculate the thickness of the shim as follows: t=x-y.
C、 Calculate the width of the shim as follows: t=x-y.
答案:B
A. The maximum distance between the plate edge and the frame is inferior to 0.05 mm.
B. The clearance between the boundary of the panel and the bay can not exceed 0.05 mm.
C. The distance between the edge of the panel and the partition must not be more than 0.05 mm.
A. 本部分用于相同的安排方法和识别特定主题材料。
B. 本部分规定了安排和识别某些主题材料的同类方法。
C. 本部分提供了安排和识别特定主题素材的统一方法。
A. Generally speaking,there are separate arrangements and chapter breakdown in each manual,full unification is difficult to achieve.
B. In general,it is mandatory for all manuals to be uniform and follow chapter arrangements and breakdown to the maximum extent.
C. In general,it is desired that the following chapter arrangements and breakdown be followed uniformly and to the maximum extent practicable in all manuals.
A. 姿态指引仪部分包括陀螺地平仪、方向陀螺仪、磁罗盘、磁航向系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
B. 姿态指引仪部分包括陀螺地平仪、回转方向仪、磁罗盘、磁头系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
C. 姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放大器、伺服系统和飞行指引仪等。
D. B.姿态指引仪部分包括陀螺地平仪、回转方向仪、磁罗盘、磁头系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
E. C.姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放
F. C.姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放大器、伺服系统和飞行指引仪等。
A. If the values occur again,remove the unit.
B. If the symptoms occur again,remove the unit.
C. Remove the unit,until the symptoms occur again.
A. The center of gravity moves along with the weight of the wings.
B. The center of gravity moves in relation to forces applied on the wings.
C. The center of gravity moves evenly to the loads of the wings.
A. 禁止使用替代器材。
B. 使用消耗器材是允许的。
C. 允许使用替代材料。
A. The cover contains manufacturer's information and will be subject to its discretion.
B. The cover is determined by the manufacturer and the information should be comprehensive.
C. The information to be included on the cover will be left to the manufacturer's discretion.
A. 扩孔(铰孔)至直径达到 8.00+/-0.003 毫米。
B. 钻孔至半径达到 8.00+/-0.003 毫米。
C. 钻孔至直径达到 8.00+/-0.003 微米。
A. Replace the PTU check valve.
B. Interchange the PTUone-way valve.
C. Change the PTU return valve.