A、 System test is normally used at minor maintenance time.
B、 System test is usually done during maintenance and repairs.
C、 System test is normally used at major maintenance periods.
答案:C
A、 System test is normally used at minor maintenance time.
B、 System test is usually done during maintenance and repairs.
C、 System test is normally used at major maintenance periods.
答案:C
A. 本部分必须确定每个(部件的)指导更换时间,结构检查间隔以及型号合格证要求的相关结构检查程序。
B. 本部分必须确定每个强制的型号合格证要求的(部件)更换时间、结构检查间隔以及结构检查对应的检查程序。
C. 本部分必须明确型号合格证要求的每个(部件的)强制更换时间,结构检查间隔以及相应的结构检查程序。
D. C.本部分必须明确型号合格证要求的每个(部件的)强制更换时间,结构检查间隔以及相
E. C.本部分必须明确型号合格证要求的每个(部件的)强制更换时间,结构检查间隔以及相应的结构检查程序。
A. Utilize the dimmer switch and ensure that the light's luminosity varies vigorously.
B. Manipulate the dimmer switch to confirm the alteration of the light's intensity.
C. Activate the dimmer switch and ascertain that the light's intensity undergoes little changes.
A. 就防冰或除冰系统对飞机在已知结冰条件下的运行批准的影响,应在“补充程序”中的限制部分里予以明确。
B. “补充程序”的极限章节应明确规定,在已知结冰条件下运行必须确保防冰或除冰系统正常工作。
C. 防霜或除霜系统对在已知结冰条件下操作飞机的批准的影响应在“补充程序”的限制章节中明确规定。
D. C.防霜或除霜系统对在已知结冰条件下操作飞机的批准的影响应在“补充程序”的限制章节中明确规定。
A. After three full cycles,extend and retract the actuator.
B. You should extend and retract the actuator through three complete cycles.
C. Do nothing to the actuator after three complete cycles.
A. 选择适用的垫圈,确定恰当的尺寸。
B. 挑选适用的调整片以确保厚度合适。
C. 从可用的垫片中进行选择,以获得正确的厚度。
A. The user of this schematic diagram is the mechanic.
B. The user of this schematic diagram is the pilot.
C. The user of this schematic diagram is the flight attendant.
A. 将光泽的一面贴在光泽的表面上。
B. 用粗糙的一面把表面打磨光滑。
C. 将补丁哑光的一面贴在光滑的表面上。
A. If the valve is the source of the fuel leak,discard the valve seals and install new ones.
B. If the fuel leaks out of the valve,reinstall the valve seals.
C. If the fuel leak flows towards the valve,discard the valve seals and install new ones.
A. Make the necessary repairs during the next applied spot check.
B. Make the required repairs during the next applicable preliminary inspection.
C. Make the necessary repairs during the next applicable scheduled maintenance.
A. 应描述系统中每个组件的功能、操作以及位置。
B. 系统中每个组件的目的、操作应和位置一样被描述。
C. 系统中每个组件的功能和构成应被描述得和位置一样好。