A、 The table is referred to follow the applicable torque values.
B、 The applicable torque values are used to obey the table.
C、 See the table below for the applicable torque values.
答案:C
A、 The table is referred to follow the applicable torque values.
B、 The applicable torque values are used to obey the table.
C、 See the table below for the applicable torque values.
答案:C
A. Remove the bolt,washer,and nut to disconnect the bend clamp from the structure.
B. Remove the screw,washer,and nut to disconnect the short clamp from the structure.
C. Remove the screw,washer,and nut to disconnect the loop clamp from the structure.
A. 姿态指引仪部分包括陀螺地平仪、方向陀螺仪、磁罗盘、磁航向系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
B. 姿态指引仪部分包括陀螺地平仪、回转方向仪、磁罗盘、磁头系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
C. 姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放大器、伺服系统和飞行指引仪等。
D. B.姿态指引仪部分包括陀螺地平仪、回转方向仪、磁罗盘、磁头系统、转弯悬停仪、放大器、伺服系统和飞行指引仪等。
E. C.姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放
F. C.姿态指引仪部分包括陀螺地平仪、定向陀螺仪、磁罗盘、磁航向系统、转弯倾斜仪、放大器、伺服系统和飞行指引仪等。
A. Lubricate one side of the washers.
B. Lubricate one side of the seals.
C. Wash one side of the washers.
A. 可以通过拆下保护盖来接近机械装置。
B. 重新安装保护盖来接近机械装置。
C. 拆下保护盖来获得机器。
A. 为使接头移除更容易,根据手册转动外壳一圈,然后再转一圈。
B. 为了更容易地放置插销取出器,将容器人工地对准一个方向,然后再调整到其他方向。
C. 为了易于拆卸销钉,手动将罩盖先朝一个方向转动,然后再朝另一个方向转动。
A. 如有必要进一步减小钢索张力,可使用松紧螺套。
B. 如有必要进一步降低钢索张力,可使用张力计。
C. 如有必要进一步调节钢索长度,可使用旋转带子。
A. The temperature can be increased by decreasing the cure time.
B. Decreasing the cure time that can increase the temperature.
C. Increase the temperature to decrease the cure time.
A. Supply electrical power to both solenoids.
B. Apply hydraulic power to either of the solenoids.
C. Apply electrical power to one of the two solenoids.
A. 尽管建议使用阴影、双向阴影、屏蔽或相似的方法,使用颜色也是允许的。
B. 虽然建议使用阴影、交叉阴影、筛选或类似的方法,但使用颜色是允许的。
C. 虽然建议使用阴影、剖面线、筛选技巧或类似的方法,但使用颜色是允许的。
A. Remove the test cap between the Precooler Control Valve and the 3908 sensor on the control pressure sense line and ensure that there is air flowing out of the port.
B. From precooler control valve to 3908 sensor,remove the sense line test cap,make certain thatthe air flows from the test hub.
C. The purpose of the test cap removal from the Precooler Control Valve to the 3908 sensor is to guarantee that there is airflow at the test port.
D. C.The purpose of the test cap removal from the Precooler Control Valve to the 3908 sensor is to guarantee that there is airflow at the test port.