A、 应当提供在客舱内或发动机冒烟或起火的情况的处理程序。
B、 应对机舱内或发动机的烟雾报警有特定的处理说明。
C、 手册中专门描述了如何应对飞机起火或冒烟的紧急情况的处理措施。
答案:A
A、 应当提供在客舱内或发动机冒烟或起火的情况的处理程序。
B、 应对机舱内或发动机的烟雾报警有特定的处理说明。
C、 手册中专门描述了如何应对飞机起火或冒烟的紧急情况的处理措施。
答案:A
A. Use the upper latch mechanism to lock the lower display unit in the middle.
B. The latch mechanism at the top is used to secure the center display unit on the bottom.
C. The center lower display unitis installed with the latch mechanism at the top.
A. 当你拆下罩环时,小心不要损坏法兰组件。
B. 当你拆下冠环扇形件时,小心不要造成法兰盘损坏。
C. 拆下法兰盘时,小心不要造成冠环扇形件损坏。
A. 用一块棉布把窗玻璃擦亮。
B. 用一块软布把窗玻璃擦干净。
C. 用一块软布把窗玻璃擦亮。
A. You can calibrate all the compass systems at the same time.
B. You can fix all the compass systems at the same time.
C. You can calibrate all the magnetic needle systems at the same time.
A. If the repair scheme must be changed,the approval of the design authority is hardly got.
B. If the design authority need change the repair scheme,it can get the approval.
C. If it is necessary to change the repair scheme,get the approval of the design authority.
A. Acquire the flight data from the recorder.
B. Eliminate the tape about the information after flight.
C. Remove a recording of flight data from the tape.
A. 注:在随后的测试中,当来自交输进口的燃油流量超过 5 毫升/分钟时,你将获得开启压力。
B. 注:在随后的测试中,当来自交输进口的燃油流量超过 5 毫升/分钟时,你将获得刮痕压力。
C. 注:在随后的测试中,当来自横穿进口的燃油流量超过 5 毫升/分钟时,你将获得刮痕压力。
D. C.注:在随后的测试中,当来自横穿进口的燃油流量超过 5 毫升/分钟时,你将获得刮痕压力。
A. Maximum Landing Weight is maximum weight supplied for the landing contact.
B. Minimum Landing Weight is minimum weight provided for the landing touchdown.
C. Maximum Landing Weight is maximum weight approved for the landing touchdown.
A. If a word is only understood by a very small number of people in a specific technical area,it will cause interference in communication.
B. If a word is only understood by a very small number of people in a specific technical area,it will cause disturbing in negotiations..
C. If a word is only understood by a very small number of people in a special skill area,it will cause interference in communication.
A. 副翼回到中立位后,确保它们与襟翼齐平。
B. 副翼回到初始位后,确保它们与缝翼垂直。
C. 襟翼移动到中立位后,确保它们与缝翼齐平。