A、 CAP 检查列出制造商建议的零件或组件的报废时间(使用小时数、循环或其他适当的决定因素)和 FAA 要求的关于时寿零件或组件的报废(维护拆换)时间。
B、 CAP 检查设定四家推荐的制造商的零件或组件退役时间(使用时间、周期或其他适当的计算方法)和 FAA 要求的时间限制零组件的退役(维护拆换)时间。
C、 CAP 检查包在建议的厂家零部件退役时间(使用时间,周期或其他合适的计量因子)和
D、 B.CAP 检查设定四家推荐的制造商的零件或组件退役时间(使用时间、周期或其他适当的计算方法)和 FAA 要求的时间限制零组件的退役(维护拆换)时间。
E、 C.CAP 检查包在建议的厂家零部件退役时间(使用时间,周期或其他合适的计量因子)和
F、 AA 要求的零部件退役(不服役)时间后进行。
答案:A
A、 CAP 检查列出制造商建议的零件或组件的报废时间(使用小时数、循环或其他适当的决定因素)和 FAA 要求的关于时寿零件或组件的报废(维护拆换)时间。
B、 CAP 检查设定四家推荐的制造商的零件或组件退役时间(使用时间、周期或其他适当的计算方法)和 FAA 要求的时间限制零组件的退役(维护拆换)时间。
C、 CAP 检查包在建议的厂家零部件退役时间(使用时间,周期或其他合适的计量因子)和
D、 B.CAP 检查设定四家推荐的制造商的零件或组件退役时间(使用时间、周期或其他适当的计算方法)和 FAA 要求的时间限制零组件的退役(维护拆换)时间。
E、 C.CAP 检查包在建议的厂家零部件退役时间(使用时间,周期或其他合适的计量因子)和
F、 AA 要求的零部件退役(不服役)时间后进行。
答案:A
A. 用一块棉布把窗玻璃擦亮。
B. 用一块软布把窗玻璃擦干净。
C. 用一块软布把窗玻璃擦亮。
A. 在此过程中,使用 12 英寸螺刀手柄。
B. 在此过程中,使用 12 英尺扳手手柄。
C. 在此过程中,使用 12 英寸扳手手柄。
A. Some aircraft parts are combined materials.
B. Some airplane structures are composite materials.
C. Some aircraft structures are compound materials.
A. Paint the fasteners with oil.
B. Apply the fasteners greasy.
C. Apply grease to the fasteners.
A. These buses consume power directly from the battery.
B. These buses accept the direct current of battery.
C. The battery supplies power directly to these buses.
A. 在制作壳体之前,确保钻头的尖端锋利。
B. 在钻孔之前,确保钻头的尖端锋利。
C. 在钻孔之前,确保电锯的尖端锋利。
A. Test the leakage of the file assembly once more.
B. Do a leak inspection of the exchanger assembly again.
C. Do a leakage check of the filter assembly again.
A. 这些装置能够在地面上用于稳定飞机并防止飞机因接触地面而造成损害的装置。包括减震支柱、防滑轮挡、机轮等。
B. 这些装置用于支撑在地面上的飞机并防止飞机因接触地面而造成损坏。它们包括减震支柱、防滑板、车轮等。
C. 这些装置用于支撑在地面上的飞机并防止飞机因接触地面而造成损坏。它们包括减震支柱、防滑板、车轮等。
D. C.这些装置用于支撑在地面上的飞机并防止飞机因接触地面而造成损坏。它们包括减震支柱、防滑板、车轮等。
A. The following synonyms are used interchangeably throughout this section and they are the sample of one system and device respectively.
B. The following antonyms are used interchangeably throughout this section and they present the same system and device partly.
C. The following acronyms are used interchangeably throughout this section and they represent the same system and device respectively.
A. 允许的最大差值为 5mm。
B. 最小容差为 5mm。
C. 允许的平均偏差为 5mm.