A、 When you access to the rear fuselage through the access panel.
B、 When you get to the aft aircraft body through the control panel.
C、 As you reach to the aft part of the aircraft by the visit door.
答案：A
A、 When you access to the rear fuselage through the access panel.
B、 When you get to the aft aircraft body through the control panel.
C、 As you reach to the aft part of the aircraft by the visit door.
答案：A
A. Magnetic tools have an unwanted effect on the compass system.
B. Metallic toolsare of positive effect on the compass system.
C. Magnets can affect the compass system adversely.
A. Find appropriate torque values in the table above.
B. Refer to the table that follows for the applicable torque values.
C. Proper torque values can be found in the booklet attached.
A. The section of the system which is used to sense and signal the formation of ice.
B. The portion of the system which is used to detect and display the condition of ice.
C. The portion of the system which is used to detect and indicate the formation of ice.
A. 反推装置是系统中引导废气产生推力的部分。
B. 反推装置是系统中改变排气方向用以向后推力的部分。
C. 反推装置能够改变排气方向进而产生反推力。
A. 不同的设计和复杂的型号使得飞机有一个重大的作用来决定特殊的失效是否更适合列举为“紧急”或“正常”程序。
B. 飞机的不同型号和机型的设计差异和复杂性,在决定某一特定故障是否更适合列为“紧急”程序或“异常”程序上发挥了重要的作用。
C. 各种型号的飞机的复杂设计差异很大程度能够决定特定失效是否能够更方便地列入“加急”或“反常”程序。
D. C.各种型号的飞机的复杂设计差异很大程度能够决定特定失效是否能够更方便地列入“加
E. C.各种型号的飞机的复杂设计差异很大程度能够决定特定失效是否能够更方便地列入“加急”或“反常”程序。
A. Rapid operation of the accelerometer can cause unexpected movement of the vertical stabilizer.
B. Accidental movement of the compass can cause unwanted operation of the oriental stabilizer.
C. Sudden operation of the gyro can cause unwanted movement of the horizontal stabilizer.
A. A Weight and Moment Limit diagram shall be used to describe the c.g.limits.
B. The maximum weight moment envelope diagram should be used to describe the c.g.limit of the aircraft.
C. A Weight and Moment Limit diagram shall be used to describe the maximum c.g.limit.
A. This is the portion of the systems used to generate,regulate,control,and indicate AC electrical power.
B. Here is that portion of the systems used to generate,regulate,control,and indicate AC electronic power.
C. That is the portion of the systems used to generate,increase,control,and indicate AC electrical power.
A. 在提供给客户的所有技术资料中,规则应保持一致。
B. 在提供给客户的所有技术数据中,文化词汇应保持一致。
C. 在提供给客户的所有技术资料中,术语应保持一致。
A. 对退漆后的表面的修理必须是面积小于 100 平方英寸(645 平方厘米),如果超过这一面积,则必须得到额外批准。
B. 对于分层的表面修理,面积不得超过 100 平方英寸(645 平方厘米)。如果超出,你必须做部分更换。
C. 装饰面的修补面积必须小于 100 平方英寸(645 平方厘米),如果超过这一面积,则必须更换该部件。
D. C.装饰面的修补面积必须小于 100 平方英寸(645 平方厘米),如果超过这一面积,则必须更换该部件。
