A、 When simulating altitude,make sure you have alternate ATC transponders in active mode.
B、 Make sure that the ATC transponders are in standby mode when you simulate altitude.
C、 It is optional to keep the ATC transponders in ready mode during altitude simulation.
答案：B
A、 When simulating altitude,make sure you have alternate ATC transponders in active mode.
B、 Make sure that the ATC transponders are in standby mode when you simulate altitude.
C、 It is optional to keep the ATC transponders in ready mode during altitude simulation.
答案：B
A. Explaining how to obtain the maximum ground miles per gallon through careful flight planning and attention to good operating procedures is the primary content.
B. Display how to achieve the main objective to get the greater ground miles per gallon by careful flight planning and attention to good operating procedures.
C. The principal purpose is to show how to increases the ground miles per gallon as much as possible with careful flight planning and attention to good operating procedures.
A. The total quantity of fuel in the center tank is 5000 lb.
B. The Total Fuel Quantity of the main tank is 5000 pounds.
C. The total fuel consumption from the center tank is 5000 pounds.
A. 显示器必须与表中的数值一致。
B. 根据显示要求必须与台架上的活门保持相同。
C. 显示结果必须与表中的数值一致。
A. This is the portion of the systems used to generate,regulate,control,and indicate AC electrical power.
B. Here is that portion of the systems used to generate,regulate,control,and indicate AC electronic power.
C. That is the portion of the systems used to generate,increase,control,and indicate AC electrical power.
A. In order to avoid edge effects on vibration routes that may misinterpret test readings,the test pitot should be moved so that the detection route moves along the surface edge to provide a constant edge for the test pitot detection.
B. To avoid edge effects on vibration paths which give a test reading that may be misinterpreted,the test probe should be moved so that the inspection path follows the surface edge,giving a constant edge for the test probe to inspect.
C. The detector should be removed along the inspection route which follows the surface edge to provide an immobile edge to detect,so as to avoid the effects on vibration route edge which may lead to the misunderstanding of the test reading.
A. 在充气活门上的防尘螺帽被拆下来了,这样新鲜的空气源才能被连接到气门杆和螺套上,以打开充气阀门。
B. 在充气阀门上的可调节螺帽被拆除了,这样新鲜的空气源才能被连接到气门杆和螺套上,以打开充气阀门。
C. 充气阀门上的防尘帽被拆除,外接气源连接到阀门杆,旋转螺母被旋开以打开充气阀门。
D. C.充气阀门上的防尘帽被拆除,外接气源连接到阀门杆,旋转螺母被旋开以打开充气阀门。
A. 包括磁电机、升压线圈、励磁机、变压器、存储电容器和合成器等。
B. 包括磁电机、分配器、升压线圈、励磁机、变压器、存储电容器和合成器等。
C. 包括磁电机、分配器、增压线圈、激励器、变压器、存储电容和合成器等。
A. 可以通过使用抹布沿钢索擦拭的方法,实现对钢索关键疲劳区域的仔细检查。
B. 可以通过沿电缆缠绕碎布的方式来对电缆关键疲劳区域进行仔细检查。
C. 在钢索严重疲劳区域进行近距离检查,可沿钢索用棉布清洁。
A. Check the cut for gaps that start at its corners.
B. Examine the opening for cracks that start at its corners.
C. Inspect the clearance of gate from the corner.
A. 如果第 9 节载明了限制条件,那么在本节应包括一条说明,向读者说明可从其中查阅可选系统或设备的限制条件。
B. 如果第 9 节包含了限制条件,那么其中应对可选系统或设备的限制条件进行说明,供读者参考。
C. 如果第 9 节给出了限制条件,则那些可供选择的系统或设备应说明符合这些限制条件,可供读者参考。
D. C.如果第 9 节给出了限制条件,则那些可供选择的系统或设备应说明符合这些限制条件,可供读者参考。
