A、 液压系统包括将一定压力(包括泵、压力调节器、管路、阀门)的液压油输送到一个汇聚点(总管),再分配到用户系统的部件和组件。
B、 这些单位和组件在压力作用下将液压油输入到包括油泵、压力调节器,管路,活门等部位,最后到达一个公共地点,即分配阀,是为了再次分配到其他设定好的系统中。
C、 这些单位和组件将液压油输入到各个压力组件中,包括油泵、压力调节器,管路,活门等。后来液压油汇聚到一个通用点(分配阀),为了再分配到其他定义好的系统中。
D、 C.这些单位和组件将液压油输入到各个压力组件中,包括油泵、压力调节器,管路,活门等。后来液压油汇聚到一个通用点(分配阀),为了再分配到其他定义好的系统中。
答案:A
A、 液压系统包括将一定压力(包括泵、压力调节器、管路、阀门)的液压油输送到一个汇聚点(总管),再分配到用户系统的部件和组件。
B、 这些单位和组件在压力作用下将液压油输入到包括油泵、压力调节器,管路,活门等部位,最后到达一个公共地点,即分配阀,是为了再次分配到其他设定好的系统中。
C、 这些单位和组件将液压油输入到各个压力组件中,包括油泵、压力调节器,管路,活门等。后来液压油汇聚到一个通用点(分配阀),为了再分配到其他定义好的系统中。
D、 C.这些单位和组件将液压油输入到各个压力组件中,包括油泵、压力调节器,管路,活门等。后来液压油汇聚到一个通用点(分配阀),为了再分配到其他定义好的系统中。
答案:A
A. 说明如何保持此记录,以便更改飞机的重量或力矩时,或在飞机正常运行时可以使用准确的起始数据来计算重量和重心。
B. 说明在更改飞机的重量或力矩时如何保持此记录,以便在飞机正常运行期间可以使用重量和平衡来准确计算起始数据。
C. 说明当飞机重量或力矩发生改变时如何进行记录,以便在飞机正常运行期间能够为计算重量和平衡提供准确的起始数据。
D. C.说明当飞机重量或力矩发生改变时如何进行记录,以便在飞机正常运行期间能够为计算重量和平衡提供准确的起始数据。
A. Instead of starting each program at the top of a new page,procedures should be prepared in chapter numbering sequence,with appropriate primary and secondary headings.
B. Each Chapter of the procedure shall be prepared in reference number order with appropriate,hierarchical headings.The beginning of a new section of the procedure does not need to start a new page.
C. Procedures shall be prepared in reference number sequence within each Chapter with proper major and minor subject heads,without the necessity of each procedure starting at the top of a new page.
A. Do not jar the instruments
B. Do not pivot the instruments
C. Do not shake the instruments
A. Compressed air will push contamination into the display unit.
B. The display unit will be contaminated by compressed air.
C. Air pressure will push the dirt into the display unit.
A. A Weight and Moment Limit diagram shall be used to describe the c.g.limits.
B. The maximum weight moment envelope diagram should be used to describe the c.g.limit of the aircraft.
C. A Weight and Moment Limit diagram shall be used to describe the maximum c.g.limit.
A. 在修订文件时,应提供修订页和相关的有效列表。
B. 在修改基本文件时,应提供相应的修订页面和相关的有效页面列表。
C. 当修改基本文件时,应尽可能提供适当的修改页面和有关的有效页面清单。
A. 因为轴的损坏,导致泵不运转。
B. 由于泵的设计问题,导致其停止运转。
C. 泵运转失常的原因在于叶轮的损坏。
A. In the event of filler bonding to the tool,dip the tool in cold water.
B. If the filler bonds to the tool,avoid using water to moisten the tool.
C. If the filler sticks to the tool,make the tool wet by applying cold water.
A. 注释会引起注意方式方法,这个能让工作更简单,或者提供说明或者注释信息的方法。
B. 注释提醒注意使工作更容易的方法,或提供说明或额外解释信息的方法。
C. 注释提醒注意使工作更容易的方法,或提供补充或解释信息的方法。
A. Data and parameters are gathered by three computers from the systems and put together on the data link to the display unit.
B. Data and parameters are generated by three computers in the system and are displayed on the display unit through the data link.
C. After analyzing the data and parameters from the system,three computers send the final result to the data link for display.