A、 An alphanumeric identifier is an assembly of characters and numbers.It can recognize something.
B、 An symbolic-numeric identifier is an assembly of symbols and numbers.It can identifies something.
C、 An alphanumeric identifier is a combination of letters and numbers that identifies something.
答案:C
A、 An alphanumeric identifier is an assembly of characters and numbers.It can recognize something.
B、 An symbolic-numeric identifier is an assembly of symbols and numbers.It can identifies something.
C、 An alphanumeric identifier is a combination of letters and numbers that identifies something.
答案:C
A. 仔细检查组件来确定是否有进一步的损坏。
B. 目视检查组件来确定损坏的部位。
C. 目视检查组件来确定损坏的程度。
A. 它指出了零件或组件的制造商的建议在翼时间。
B. 它给出了制造商建议的零件或组件退役时间。
C. 它说明了制造商推荐零件或组件的报废时间。
A. The rudder can be used in case of thrust asymmetry.
B. The vertical stabilizer can be used in case of throttle symmetry.
C. The rudder can be used in situations where thrust is symmetric.
A. 用于把液压油储存到一定量后运送于系统中使用的部分。包括很多部件,比如:油箱、储存器、阀门、油泵、杠杆、电门、电缆、铺设管路、外部连接器等。不包括将阀门提供给使用中的系统。
B. 用来储存和运送液压油到各个使用系统的系统部分,包括油箱、蓄压器、活门、油泵、手柄、电门、钢索、管路、外部接头等部件。不包括各用户系统的供应阀。
C. 系统用于把液压油储存并运送于系统中进行使用的部分。包括以下部件:油箱、储存器、阀门、油泵、手柄,开关、电缆、铺设管路,外部连接器等。不包括输送阀门给系统使用。
D. B.用来储存和运送液压油到各个使用系统的系统部分,包括油箱、蓄压器、活门、油泵、手柄、电门、钢索、管路、外部接头等部件。不包括各用户系统的供应阀。
E. C.系统用于把液压油储存并运送于系统中进行使用的部分。包括以下部件:油箱、储存器、阀门、油泵、手柄,开关、电缆、铺设管路,外部连接器等。不包括输送阀门给系统使用。
A. Normally,it is named “fly by electrical control system”.
B. Normally,we name it “fly by electricalsystem”.
C. This is commonly referred to as “the flight by wire system”.
A. The table is referred to follow the applicable torque values.
B. The applicable torque values are used to obey the table.
C. See the table below for the applicable torque values.
A. 批准的形容词以其基本形式给出,在实际应用的过程中,在括号标注内其最高级和比较级形式。
B. 批准的形容词以其基本形式给出,在适用的情况下,其比较级和最高级形式要标注在括号内。
C. 形容词会以其批准的基本形式给出,在适当的时候,也可给出其比较级和最高级形式。
D. C.形容词会以其批准的基本形式给出,在适当的时候,也可给出其比较级和最高级形式。
A. 如果填充剂粘在工具上,用冷水湿润工具。
B. 如果使用工具时需用封圈辅助,用冷水先清洗工具。
C. 如果需要使用填充剂粘接工具,用冷水浸泡工具。
A. Instead of starting each program at the top of a new page,procedures should be prepared in chapter numbering sequence,with appropriate primary and secondary headings.
B. Each Chapter of the procedure shall be prepared in reference number order with appropriate,hierarchical headings.The beginning of a new section of the procedure does not need to start a new page.
C. Procedures shall be prepared in reference number sequence within each Chapter with proper major and minor subject heads,without the necessity of each procedure starting at the top of a new page.
A. 用设置开关以重置运行时间。
B. 用重置按钮以重置运行时间。
C. 用重置按钮以重置格林威治时间。