A、 Replace broken clamp with new clampwith reference to standard practices and AMM and relieve rubbing with the bundle at floor bar cut at body station 360.
B、 Replaced broken clamp with a new clamp diminishing rubbing at floor beam cutout at body station 360 with reference to standard practices and AMM.
C、 According to the standard practices and AMM,the damaged clamp at the body station 360 was replaced to eliminate the friction between the wire bundle and the cutout of the floor beam at this place.
答案:C
A、 Replace broken clamp with new clampwith reference to standard practices and AMM and relieve rubbing with the bundle at floor bar cut at body station 360.
B、 Replaced broken clamp with a new clamp diminishing rubbing at floor beam cutout at body station 360 with reference to standard practices and AMM.
C、 According to the standard practices and AMM,the damaged clamp at the body station 360 was replaced to eliminate the friction between the wire bundle and the cutout of the floor beam at this place.
答案:C
A. 如果读者必须了解某个额外要求才能执行工作程序和步骤,先给出这个要求。
B. 如果读者在执行某个工序或工作步骤之前必须了解某个具体情况,则首先说明这个具体情况。
C. 读者在执行程序或工作步骤之前是否必须知道哪些特定条件,需要先明示。
D. C.读者在执行程序或工作步骤之前是否必须知道哪些特定条件,需要先明示。
A. 如果无法听到警告声,需调整音量控制器。
B. 调整音量控制器可能导致警告声过于响亮。
C. 调整音量控制器可能使警告声变得更加嘈杂。
A. 燃油在燃烧室内燃烧。
B. 燃油通过喷嘴进入雾化器。
C. 燃油通过雾化器进入燃烧室。
A. 盖子朝下的时候,是开关在开位的一种保护。
B. 封面在下面的时候,是开关在开位的保险。
C. 盖子朝下的时候,是开关在开位的保险。
A. 扩孔(铰孔)至直径达到 8.00+/-0.003 毫米。
B. 钻孔至半径达到 8.00+/-0.003 毫米。
C. 钻孔至直径达到 8.00+/-0.003 微米。
A. When showing a low flow or not sufficient cooling condition,the low flow sensor produces an alarm signal of the flight compartment for warning.
B. When a low flow or under cooling condition occurs,the low flow sensor provides an alarm signal to the cabin compartment for alert.
C. When a low flow or not sufficient cooling condition occurs,the low flow sensor supplies an alarm signal to the flight compartment for annunciation.
A. 对涡轮发动机来说,排气系统包括发动机本体以外的部件。
B. 对涡轮发动机来说,排气系统包括发动机主系统内的装置。
C. 对涡轮发动机来说,排气系统不包括发动机主系统以外的装置。
A. Hand tools can be divided to four basic categories: kicking tools,holding tools,cutting tools,bending tools.
B. Hand tools can be divided to four basic categories:kicking tools,clutching tools,cutting tools,rolling tools.
C. Hand tools will fall into four basic categories: pounding tools,holding tools, cutting toolsand turning tools.
D. C.Hand tools will fall into four basic categories: pounding tools,holding tools, cutting toolsand turning tools.
A. Remove the bolt,washer,and nut to disconnect the bend clamp from the structure.
B. Remove the screw,washer,and nut to disconnect the short clamp from the structure.
C. Remove the screw,washer,and nut to disconnect the loop clamp from the structure.
A. 描述飞机发动机时,应对冷却( 散热)系统进行描述,包括整流罩盖板。
B. 描述飞机发动机时,应描述冷却( 散热)系统相关的信息,包括通风外壳。
C. 描述飞机发动机时,应描述空调系统相关的信息,包括通风罩板。