195.在基准导轨滑块上放上磁吸表,测头指向非基准导轨滑块上,在任意行程上检验两导轨的( ),要求S0.015mm/1000.
A. 水平度误差
B. 、平行度误差
C. 、垂直度误差
D. 、倾斜度误差
https://www.shititong.cn/cha-kan/shiti/0005e217-d925-f570-c09c-1b2cd3ff4325.html
点击查看答案
605.联轴器是无向隙配合的零件。( )
https://www.shititong.cn/cha-kan/shiti/0005e217-da6f-7118-c09c-1b2cd3ff4332.html
点击查看答案
313.500F plus JT803系统机床,CSW80G水冷机报警E05,检查水冷机输入电源正常,插头焊线无虚焊,故障原因为( )
A. 水冷机压缩泵故障
B. 水冷机电路板故障
C. 水冷机正常
D. 水冷机输出电源接触不良
https://www.shititong.cn/cha-kan/shiti/0005e217-d926-0128-c09c-1b2cd3ff4323.html
点击查看答案
867.常用的XC2.3/3.0KW主轴,要用多大的夹头 ( )范围内( )。
https://www.shititong.cn/cha-kan/shiti/0005e217-dc44-92c0-c09c-1b2cd3ff4336.html
点击查看答案
432.层项不是JTGK600CPC8055I/A系统三轴雕铣机的立柱高度( )
A. 660NM
B. 585M
C. 670MM
https://www.shititong.cn/cha-kan/shiti/0005e217-d9e3-9850-c09c-1b2cd3ff4314.html
点击查看答案
209.FC8060系统中,下列程序段正确的应是?( )
A. G53G0 Z-5
B. G53DOGOZ-5
C. G53D1 GO 2-5
D. 以上都错
https://www.shititong.cn/cha-kan/shiti/0005e217-d925-f958-c09c-1b2cd3ff430b.html
点击查看答案
339.JT系统机床控制伺服主电源的继电器是( )
A. KA12
B. KA4
C. KA2
D. KA1
https://www.shititong.cn/cha-kan/shiti/0005e217-d926-0510-c09c-1b2cd3ff4315.html
点击查看答案
804.办事处收件时必须开箱验货完好后才能签收,如遇损坏情况应第一时间与物料小组联系处理方案( )
https://www.shititong.cn/cha-kan/shiti/0005e217-da6f-80b8-c09c-1b2cd3ff4309.html
点击查看答案
444.500B JT803系统机床,加工完成后,机械手没有过来取放料,有可能( )导致。
A. 机床加工完成信号缺失
B. 允许放料信号
C. 机械手上下料信号缺失
D. 无问题
https://www.shititong.cn/cha-kan/shiti/0005e217-d9e3-9850-c09c-1b2cd3ff4320.html
点击查看答案
538.600机CFG8055I/A系统三轴雕铣机,X轴回零行程撞块,其中长边为回零,短边为限位。( )
https://www.shititong.cn/cha-kan/shiti/0005e217-da6f-6d30-c09c-1b2cd3ff432a.html
点击查看答案