A、 将飞机速度除以侧风分量来得到修正。
B、 用侧风分量除以飞机速度,得到修正值。
C、 将侧风部件和飞机分开,来得到正确的速度。
答案:B
A、 将飞机速度除以侧风分量来得到修正。
B、 用侧风分量除以飞机速度,得到修正值。
C、 将侧风部件和飞机分开,来得到正确的速度。
答案:B
A. After wash aircraft, all 3 landing gears were found un-lubricated.
B. After aircraft wash, all 3 landing gears were found un-lubricated.
C. After aircraft clean, all 3 landing gears was found un-lubricated.
A. Emergency illumination refers to an individual and dependent subsystem which is used to provide lighting when the main electrical power fails.
B. Emergency lighting can provide illumination for an individual and independent subsystem in case of main electrical power failure.
C. Emergency lighting is the separate and independent subsystem used to provide illumination in case of primary electrical power failure.
A. 发动机系统包含元件和部件用于控制和改变润滑剂在发动机入口和出口的流动。
B. 发动机系统包含控制和引导润滑油从进口流向出口的组件和部件。
C. 润滑剂靠发动机的元件和部件的控制和引导在发动机里产生流动。
A. Maximum Limiting speed Unsticks is the speed restrain which will not be intentionally surpassed in typical flight operations. V is communicated in knots and M in Mach Number.
B. Maximum Restriction Speed is the fastest a plane can fly without breaking the rules in normal flight. The speed is measured in knots and Mach Number.
C. Maximum Operating Limit Speed is the speed limit that may not be deliberately exceeded in normal flight operations. V is expressed in knots and M in Mach Number.
A. 这些单位及组件给予不相干的系统警告,声音或者视觉的。
B. 这些组件及部件为不相关系统的状态提供听觉或视觉警告。
C. 这些单位及组件给各个系统的不相关的工作条件提供声音或视觉警告。
A. In either case, a chart will be included in showing standard symbols used throughout the manual.
B. In both cases, a figure will be contained to show the normal symptoms used in the whole manual.
C. Through the handbook, a form shall be used to show the normal signs in these two cases.
A. 变更一些词性的缩写,使其与标准缩写一致。
B. 一些词性缩写的变化与标准缩写一致。
C. 更新标准缩写使其满足一些词性缩写变更的要求。
A. 除非不适用于特定型号的飞机,手册应按所示顺序,包含以下飞行阶段推荐的正常程序。
B. 手册按所示顺序显示以下飞行阶段建议的正常程序,但特定型号的飞机除外。
C. 当手册不适用于某些特定飞机型号时,它应包括下列飞行状况下必须遵守的正常程序。
A. 检验/检查部分应提供必要的信息和程序,以获取接近和检验或检查系统、部件或区域的方法。
B. 在检验/检查部分,应提供接近、检验或检查一个系统、一个组件或一个区域所必需的信息和程序。
C. 在检验/检查部分获得必要的信息,以便接近、检验或检查系统、单元或区域。
A. 这个单元的主要函数是控制燃油流动。
B. 这个装置的主要功能是控制燃油流量。
C. 这个组件的辅助功用是控制燃油流动。