A、 The SMYD1 will limit rudder movement when flaps are up if trailing edge flaps receive data from up limit switch of SMYD1 during yaw damping.
B、 The SMYD1 will limit rudder movement after receiving data from up limit switch of trailing edge flaps during yaw damping when flaps are up.
C、 The SMYD1 will limit yaw damping to reduce rudder movement when flaps are up If trailing edge flaps receive data from up limit switch of SMYD1.
答案：B
A、 The SMYD1 will limit rudder movement when flaps are up if trailing edge flaps receive data from up limit switch of SMYD1 during yaw damping.
B、 The SMYD1 will limit rudder movement after receiving data from up limit switch of trailing edge flaps during yaw damping when flaps are up.
C、 The SMYD1 will limit yaw damping to reduce rudder movement when flaps are up If trailing edge flaps receive data from up limit switch of SMYD1.
答案：B
A. Ensure that the arrow points in the direction of fluid flow.
B. Make sure that the arrow points in the direction of the fuel flow.
C. Ensure that the arrow points in the direction of fluid supply.
A. 如果这个部件应该纳入CAP，那么使用最终数据做出判断。
B. 公司应利用现有数据判断该部件是否与CAP相关联。
C. 已用所得数据来确定是否应将该部件纳入CAP。
A. One of the safety precautions is to keep the combustible material from the work area at distance of 50ft at least.
B. One of the safety precautions is to keep the flammable material from the work area at distance of 50ft at least.
C. One of the safety precautions is to keep the combustible material from the work area at a minimum distance of 50ft.
A. 如果襟翼的伸出量与控制杆的位置不一致，重复安装程序。
B. 如果襟翼的放出量和襟翼手柄位置不一致，再做一次测试程序。
C. 如果襟翼扩大的幅度与襟翼手柄位置不一致，重复一次测试程序。
A. 应说明总容量和可用燃料，如果不可用燃料超过FAR23的限制，在飞行中不可用数量的信息应被提供。
B. 如果不可用燃油超过FAR23的限制，则应说明总容量和可用燃油并确定提供在飞行中不可用燃油量的信息。
C. 应说明总容量和可用燃油，如果不可用燃油超过FAR23的限制，应提供确定在飞行中不可用燃油量的信息。
A. 计算航程时应考虑开车、滑行、起飞和爬升所需燃油以及储备燃油。对于开车、滑行和起飞，需考虑飞机以起飞功率运行5分钟的所需燃油量。对于储备燃油，应考虑巡航功率运行 45 分钟所需燃油量。
B. 航程值应包括起动、滑行、起飞、爬升和备用的燃油。对于起动，滑行和起飞，允许在起飞功率5分钟的燃油流量。预留燃油按飞行所需的巡航功率计算为45分钟。
C. 航程值应包括启动、滑行、起飞、爬升和备用时间所需的燃油量。对于开车、滑行和起飞，需考虑飞机以起飞功率运行5分钟的所需燃油量。对于备用时间，应按飞行所用巡航功率下的45分钟计算。
A. 对所有维修过的产品进行全面检查。
B. 对所有维修过的产品进行仔细检查。
C. 对所有维修过的产品进行初始检查。
A. Identify the disassembled parts with tags.
B. To notice the removed parts with the lable.
C. To mark the assembled parts with the cards.
A. The elevator is used for yaw control.
B. The rudder is used for yaw control.
C. The rudder is used for pitch control.
A. The long hand of the clock only goes with the counting function of the clock.
B. The sweep second hand only works with the timing function of the clock.
C. The second pointer is only used for the chronic function of the clock.
