A、 升降舵/前置平翼的后缘/前缘的水平翼型包括翼梁、翼肋、桁条、镀层/蒙皮、接近口盖、翼尖等结构。
B、 升降舵/机翼所附着的尾翼/机头部分的水平翼型包括梁、肋、弦、板/皮、通道盖、尖端等。
C、 升降舵/前翼所连接的尾部/机头部分的水平翼型包括诸如翼梁、肋、纵梁、板/蒙皮、检修盖、尖端等项目。
答案:A
A、 升降舵/前置平翼的后缘/前缘的水平翼型包括翼梁、翼肋、桁条、镀层/蒙皮、接近口盖、翼尖等结构。
B、 升降舵/机翼所附着的尾翼/机头部分的水平翼型包括梁、肋、弦、板/皮、通道盖、尖端等。
C、 升降舵/前翼所连接的尾部/机头部分的水平翼型包括诸如翼梁、肋、纵梁、板/蒙皮、检修盖、尖端等项目。
答案:A
A. If the wheel temperature reaches as high as 177 deg., the core of safety plug shears off and the tire slips.
B. If the wheel temperature increases to more than 177 deg., the core of the fusible plug melts and the tire deflates.
C. The core of the filter element melts once the wheel temperature is above 177 deg., causing the tire to deflate.
A. 因为轴的损坏,导致泵不运转。
B. 由于泵的设计问题,导致其停止运转。
C. 泵运转失常的原因在于叶轮的损坏。
A. 定位器与跑道中心线对齐,下滑道与跑道出口成一定角度。
B. 航道与跑道中心线对齐,下滑道与跑道入口成恒定角度。
C. 航道与跑道中心线平行,下滑道与跑道出口成恒定角度。
A. 防腐剂可能存在于腐蚀严重的部位。
B. 腐蚀敏感的部位可以安装防腐组件。
C. 易受腐蚀的部位可能有防腐剂。
A. 删除了注释及其相关示例。
B. 注释和相关示例做了保留。
C. 删除了注释和列举了的示例。
A. 不要让清洁剂接触带有瑞尔森(Rilsan)涂层的零件。
B. 不要使用含氯的溶剂清洁带有瑞尔森(Rilsan)涂层的零件。
C. 不可以使用含氯的瑞尔森(Rilsan)溶液清洁带有涂层的零件。
A. 描述飞机螺旋桨时,可包括可变桨距螺旋桨的剖面图。
B. 描述飞机螺旋桨时,可包括变桨距螺旋桨的水平图。
C. 描述飞机螺旋桨时,可包括固定桨距螺旋桨的剖面图。
A. Air filter needs to be replaced on regular maintenance schedule, because it often causes low flow through the equipment cooling supply system. Quickly release the tabs on the air filter housing cover to reach the filters.
B. Low flow through the equipment cooling supply system is caused by a contaminated air filter, therefore regular replacement is necessary, release the quick release tabs on the air filter housing cover to approach to the filters.
C. A blocked air filter which causes low flow through the equipment cooling supply system needs replacement on a regular maintenance schedule. Release the quick release tabs on the air filter housing cover to reach the filters.
A. Schematic diagrams may be used to indicate "flow" and to illustrate the operation of systems such as air control, electrical, fluid power, fuel and turbosystems.
B. Principle charts can be intended to show "flow" and explain the operation of systems as well as air control, electrical, hydraulic power, fuel and turbine systems.
C. Schematic diagrams can be employed to show "flow" and to explain the operation of systems along with air control, electrical, fluid power, fuel and turbosystems.
A. Do not authorize to do the engine test.
B. The engine test will not be completed if you are not authorized.
C. If you are not approved to do this work, do not do this engine test.