Install safety wire to the knurled retaining ring and the clogging indicator body.

A. 如果襟翼的伸出量与控制杆的位置不一致，重复安装程序。

B. 如果襟翼的放出量和襟翼手柄位置不一致，再做一次测试程序。

C. 如果襟翼扩大的幅度与襟翼手柄位置不一致，重复一次测试程序。

A. “螺旋桨调速器”是利用螺旋桨轮毂内变距机构，通过增大或减小螺旋桨桨距来调节发动机或螺旋桨转速的装置。

B. “螺旋桨调速器”是通过螺旋桨的螺距变化机构，通过增加螺旋桨螺距来调节发动机或螺旋桨转速的装置。

C. “螺旋桨调速器”是通过螺旋桨的螺距变化机制，通过减少螺旋桨桨距来调节发动机或螺旋桨转速的装置。

A. The vendor can build programs to supply response to worthless conditions found in compliance with regulations.

B. The manufacturer may establish procedures to provide feedback on unairworthy conditions that were discovered when complying.

C. The manufacturer may create a process to give feedback on abnormal conditions when it＇s conformed.

A. 应提供描述可能出现的故障、如何识别这些故障以及这些故障的补救措施的故障排除信息。

B. 提供的排故信息应描述可能出现的故障、如何识别相关故障以及相应的补救措施。

C. 应提供描述可能出现的故障、如何识别这些故障以及补救措施的排除信息。

A. Incorrect adjustment of the stops will lead to accurate test results.

B. In precision, test results cannot occur unless the stops are adjusted properly.

C. If the stops are not adjusted Incorrectly, the test results will not be precise.

A. 该子系统包括测距机，收发机，无线电高度表，基于性能的导航，甚高频全向信标，自动定向仪等部件。

B. 该子系统包括测距机，应答机，无线电罗盘，远距离无线电导航系统，甚高频全向信标，自动定向仪等部件。

C. 该子系统包括测距机，发射机，无线电罗盘，区域导航，指点信标，自动定向仪等部件。

A. 控制主燃料控制哪个仪表为发动机和推力调节器提供燃料。包括电线、滑轮、连杆等物品，也是燃料控制单元的部件。

B. 控制主燃料控制所有仪表为发动机和推力调节器提供燃料。包括杠杆、电缆、滑轮、连杆等物品，也是燃料控制单元的部件。

C. 主燃油控制系统能够计量送往发动机和加力燃烧室的燃油，其包括油门杆、钢索、滑轮、连杆等，这些也属于燃油控制组件。

A. According to Boeing Docs and associated ADs, changing the dimension of the thrust reverser upper locking actuator lock sensor target can result in slow detection of the failure or undetected failure.

B. Based on the Boeing Docs and the associated ADs, if the size of the thrust reverser upper locking actuator lock sensor target is increased, it may result in delayed or undetected the actuator failure.

C. As described in Boeing Docs and the associated ADs, if the orientation of the locking actuator on the thrust reverser locking sensor target changes, the actuator failure will be delayed or undetected.

A. Make sure that there is supplied airflow in the work area.

B. Make sure that there is sufficient airflow in the work area.

C. Make sure that there is efficient airflow in the work area.

A. The elevator is used for yaw control.

B. The rudder is used for yaw control.

C. The rudder is used for pitch control.