A、 Manufacturers＇ recommended time limits, maintenance checks and inspections (both planned and unplanned) are arranged in Chapter 5.
B、 Manufacturers＇ recommended time limits, maintenance checks and tests (both scheduled and unscheduled) are arranged in Chapter 5.
C、 Manufacturers＇ recommended time limits, maintenance checks and inspections (both scheduled and unscheduled) are arranged in Chapter 5.
答案：C
A、 Manufacturers＇ recommended time limits, maintenance checks and inspections (both planned and unplanned) are arranged in Chapter 5.
B、 Manufacturers＇ recommended time limits, maintenance checks and tests (both scheduled and unscheduled) are arranged in Chapter 5.
C、 Manufacturers＇ recommended time limits, maintenance checks and inspections (both scheduled and unscheduled) are arranged in Chapter 5.
答案：C
A. Make sure that the bolt heads are attached to the skin.
B. Make sure that the screw heads are connected with the metal.
C. Make sure that the fastener heads are flush with the skin.
A. 检验/查找部分应提供访问和检验或查找系统、单元或区域所需的信息和程序。
B. 检验/检查部分应提供接近和检验或检查系统、装置或区域所需的信息和程序。
C. 监控/检查部分应提供访问和监控或检查系统、装置或区域所需的信息和程序。
A. 扭矩测量仪是一个显示螺旋桨传动轴可用输出扭矩的指示系统。
B. 扭矩计可以显示传动轴的输出扭矩。
C. 指示系统必须显示扭矩计传动轴的可用输出扭矩。
A. Drill the hole until it has a radius of 8.00 +/- 0.003 mm.
B. Ream the hole until it has a diameter of 8.00 +/- 0.003 mm.
C. Trim the hole until it has a width of 8.00 +/- 0.003 mm.
A. Direct Damage is defined as follows: 1) Metallic surfaces are burned, melted or show signs of metal distortion. 2) Non-metallic surfaces are burned, punctured or delaminated.
B. Direct Damage is defined as follows: 1) Metallic surfaces are burned, combined or show signs of metal corrosion. 2) Non-metallic surfaces are burned, punctured or contaminated.
C. Direct Damage is defined as follows: 1) Metallic surfaces are burned, synthesised or show signs of metal distortion. 2) Non-metallic surfaces are burned, cut or delaminated.
A. 接近和位置的说明会在这里给出不少信息。
B. 除非很困难，否则接近和位置的说明会在此给出。
C. 除非很明显，否则接近和位置的说明会在此给出。
A. The temperature can be increased by decreasing the cure time.
B. Decreasing the cure time that can increase the temperature.
C. Increase the temperature to decrease the cure time.
A. 本程序给出了不同的扭矩范围以及相应的规定。
B. 本文件给出了不同的扭矩值和其适用的条件。
C. 本程序给出了适用的差异扭矩值和条件。
A. 确保TEDLAR层压板的装饰颜色和图案是正确的。如果新的TEDLAR不能与原件配合，修理结果不会令人满意。
B. 确保TEDLAR装饰层压板的颜色和图案是正确的，如果新的TEDLAR与原品的表面不匹配，修复将不会令人满意。
C. 确保TEDLAR退漆到正确的分层处，如果TEDLAR漆层不能与底漆配合，修复效果将不会令人满意。
A. Remove the bolts from the flange.
B. Remove the rivets from the flange.
C. Remove the rivets from the flanks.
