A、 Turn the adjuster clockwise to increase 60 Deg.
B、 Turn the adjuster counterclockwise in increments of 60 Deg.
C、 Decrease 60 Deg. to turn the adjuster counterclockwise.
答案：B
A、 Turn the adjuster clockwise to increase 60 Deg.
B、 Turn the adjuster counterclockwise in increments of 60 Deg.
C、 Decrease 60 Deg. to turn the adjuster counterclockwise.
答案：B
A. It sets forth supplier recommended and FAA required retirement (removal from service) times for parts or assemblies (using hours, intervals or other appropriate determinant) and life limited parts or assemblies.
B. It sets forth manufacturer recommended retirement times for parts or assemblies (using hours, cycles or another appropriate determinant) and FAA required retirement (removal from service) times for life limited parts or assemblies.
C. It sets forth retirement times for parts or assemblies (using hours, loops or another appropriate determinant) established by the manufacturer and retirement (removal from service) times for life limited parts or assemblies required by FAA.
A. 用密封剂填充补片及相邻结构之间的缝隙。
B. 用密封剂填充补片的缝隙，并粘接相邻结构。
C. 在附近的密封结构和补片之间留出空隙。
A. Give precise instructions for using emergency exits.
B. Give special directions for using urgent exits.
C. Give accurate data for using urgent exits.
A. 空客建议，使用千斤顶和辅助千斤顶时，其负载能力应大于顶块允许的最大载荷。
B. 空客建议，使用千斤顶和安全顶座时，顶块的负载能力应大于允许的最大载荷。
C. 在顶块的负载能力大于允许的最大载荷的情况下，空客建议使用千斤顶和安全支架。
A. 定义措辞应尽可能简单，并必须符合手册中所定义的术语的使用。
B. 定义应尽可能简单地被记录，且必须保证手册中已定义术语的使用。
C. 定义应尽可能用词简单，且必须强制使用手册中规定的术语。
A. Choose the hydraulic system you will apply pressure.
B. Pressurize the selected hydraulic system.
C. Choose the hydraulic system you will depressurize.
A. Make up for all gaps which are larger than 0.05 mm.
B. Repair all cracks that are wider than 0.05 mm.
C. Overhaul all fissures which are greater than 0.05mm.
A. 这些条目被ABC评估后，如果和飞机配置相关，将这些条目添加到文件中以满足所有人的利益。
B. 这些项目将由ABC进行评估，根据相关飞机配置，并为了满足所有人的利益将这些项目添加到相关文件中。
C. 这些项目将由ABC进行评估，如果适用于有关的飞机配置，将为了所有人的利益而将这些项目添加到文件中。
A. If an engine overheat/fire detector can not operate, the engine and APU fire alarm unit alternatively changes to single loop operation. In the single loop module, only one loop must check the engine and APU fire detection module for an overheat or fire co
B. If an engine overheat/fire detector fails to operate, the engine and APU fire detection module automatically changes to single loop operation. In the single loop mode, only one loop must detect an overheat or fire condition for the engine and APU fire det
C. If an engine overheat/fire detector is inoperative, the engine and APU fire detection module automatically changes to single loop operation. In the single loop mode, only one loop must detect an overheat or fire condition by the engine and APU fire detect
A. Do not authorize to do the engine test.
B. The engine test will not be completed if you are not authorized.
C. If you are not approved to do this work, do not do this engine test.
