A、 Copy density should be the same throught the page.
B、 Copy density must be different throught the page.
C、 Density of copy must be different throught the page.
答案：A
A、 Copy density should be the same throught the page.
B、 Copy density must be different throught the page.
C、 Density of copy must be different throught the page.
答案：A
A. 如果不同时这样做,则会卡住定位销。
B. 如果不同时这样做,则会导致定位销磨损。
C. 如果不同时这样做,则会导致定位销脱落。
A. 文件需要随时修改。
B. 文件必须随时修改。
C. 文件必须易于修改。
A. 无论是否经过书面许可,都不得以任何形式复制本文件的任何部分。
B. 经出版者书面许可,可以复制本文件的任何部分。
C. 未经出版者书面许可,不得以任何形式复制本文件的任何部分。
A. Secondly, it is a guide to industry standardization of proven concepts
to be presented in a form most useful to pilots.
B. Basically, it is a guide to industry standardization of provided
concepts to be presented in a form most useful to pilots.
C. Mainly, it is a guide to industry standardization of proven concepts
to be presented in a form most useful to pilots.
A. 该工具用于将钢索张力调节器上的标记与固定标盘上的相关指针对齐。
B. 该工具用于将钢索张力调节器上的标记与固定标盘上的相关刻度对齐。
C. 该工具用于将钢索弹簧调节器上的标记与固定标盘上的相关刻度对齐。
A. 修正空速(CAS)仅为按需使用,以符合认证机构的任何对应要求,因为飞行员
延程飞行时需按照指示空速(IAS)工作。
B. 修正空速(CAS)仅在紧急情况时使用,以符合认证机构的任何对应要求,因为
飞行员不能按照指示空速(IAS)工作。
C. 修正空速(CAS)仅在必要时使用,以符合认证机构的任何对应要求,因为飞行
员完全按照指示空速(IAS)工作。
A. 副翼回到中立位后,确保其与襟翼齐平。
B. 扰流板回到原位后,保证和襟翼对齐。
C. 在副翼返回中心之后,保证它们和襟翼相连。
A. In flight,Flight Idle Power required for the engine to operate at slowly
speed is an important condition to ensure good engine operation and
airplane handing characteristics.
B. Flight Idle Power is the power required for an engine to operate at
a minimum speed during flight to ensure satisfactory engine operation and
aircraft handing characteristics.
C. In flight,good engine operation and aircraft handing characteristics
are guaranteed to provide the engine with Flight Idle Power needed to
operate at the lowest speed .
A. ABC has determined the varied mission the airplanes performed, type
of care given, and age and utilization rates because providing additional
inspection requirement is prerequisite to further ensure that the
airplane can continue to carry the design loads it was initially certified
for based on inspections, tests, and analyses.
B. ABC has determined that providing additional inspection requirements
is prerequisite to further ensure that the airplanes can continue to carry
the design loads it was initially certified for based on inspections,
tests, and analyses because of the varied mission the airplanes performed,
type of care given, and age and utilization rates.
C. To further ensure that the airplanes can continue to carry the design
loads it was initially certified for, owing to the diversified mission
the airplanes performed, type of care given, and age and utilization rates,
A. Secondly, it is a guide to industry standardization of proven concepts
to be presented in a form most useful to pilots.
B. Basically, it is a guide to industry standardization of provided
concepts to be presented in a form most useful to pilots.
C. Mainly, it is a guide to industry standardization of proven concepts
to be presented in a form most useful to pilots.
