A、 如有必要进一步减小钢索张力,可使用松紧螺套。
B、 如有必要进一步降低钢索张力,可使用张力计。
C、 如有必要进一步调节钢索长度,可使用旋转带子。
答案:A
A、 如有必要进一步减小钢索张力,可使用松紧螺套。
B、 如有必要进一步降低钢索张力,可使用张力计。
C、 如有必要进一步调节钢索长度,可使用旋转带子。
答案:A
A. 将分隔标签平行放置,并用节号或标题或两者一起标记
B. 将分隔标签错开,并用节号或标题或两者起标记
C. 将分隔标签顺序放置,并用节号或标题或两者一起标记
A. 一体式电路一般包括一体式部件以及以单片结构执行完整电路功能的器件。
B. 集成电路一般包括那些具有集成元件、以单片结构执行完整电路功能的器件。
C. 集成电路总是包括那些具有一体化元件、以整体结构实现完整电路功能的器件。
A. 飞机性能中至少一项应包括与数据有关的重要条件的说明。
B. 飞机性能的每一项应包括与数据有关的重要条件的说明。
C. 飞机制导的每一项应包括与数据有关的重要条件的说明。
A. The water quantity transmitter is easily damaged;
B. The water quantity transmitter is expensive;
C. The water quantity transmitter is unstable;
A. 关于“限制”和“紧急程序”的章节放在“正常程序”、“性能”之前,“载重和平衡”和其他章节更容易获得飞行中可能需要的信息。
B. 关于“限制”和“紧急程序”的章节放在“正常程序”、“性能”,“载重和平衡”和其他章节之前,以便更容易地获取飞行中可能需要的信息。
C. 关于“限制”和“紧急程序”的章节放在前面,“正常程序”、“性能”、“载重和平衡”和其他章节用于更容易地获取飞行中可能需要的信息。
A. Adjust the clearance dimension between the extend proximity sensor[1A] and the target[1C] until the clearance dimension is out of range. Some of the ducts in the air distribution system are wrapped with compound material.
B. Adjust the clearance dimension between the extend proximity sensor[1A] and the target[1C] in case of the clearance dimension is out of tolerance. Some of the ducts in the air distribution system are wrapped with non-conductive material.
C. If the clearance dimension is not accurate,adjust the clearance dimension between the extend proximity sensor[1A] and the target[1C]. Some of the ducts in the air distribution system are wrapped with insulation material.
A. Turn the control to the full close position
B. Turn the control to the fully closed position
C. Turn the control to the fully close position
A. The display annunciates a fault message
B. The display shows a fault message
C. A fault message shows the display
A. The front panel of the cellphone has a touchscreen and a home button.
B. There is a touchscreen and a home key on the forward panel of a cordless phone.
C. A touchscreen and a main page pushbutton are fixed on the mobile phone forward panel.
A. The distance between the edge of the panels and the partition must be less than 0.05 mm.
B. The distance between the edge of the panel and the partition must be equal to 0.05mm
C. The distance between the edge of the panel and the partition must be 0.05 mm or less.