A、 确认蒙皮没有损伤
B、 确认皮肤没有受伤
C、 确认蒙皮没有划伤
答案:A
A、 确认蒙皮没有损伤
B、 确认皮肤没有受伤
C、 确认蒙皮没有划伤
答案:A
A. 确保压力不低于30磅每平方英寸。
B. 确保压力小于30磅每平方英寸。
C. 确保压力不高于30磅每平方英寸。
A. Tighten the nuts but do not torque them at this time.
B. Screw the nuts but do not torque them at this time.
C. Tighten the nuts but do not screw them at this time.
A. 涡轮发动机速度表通常以涡轮最大转速的百分比来测量转速。
B. 涡轮发动机转速表通常以涡轮额定最大转速的百分比来测量转速。
C. 涡轮发动机速度计通常以涡轮转动的最大速度的百分比来衡量。
A. In “Restricted Area B”, where satisfactory working condition is available and approved by Airframe Manufacturer, the operator is required to perform repairs based on the procedures contained in related chapters of the SRM.
B. In “Restricted Area B”, when conducting repairs as required, the operator can either obey procedures in relevant chapters of the SRM, or apply his own solution approved by Airframe Manufacturer beforehand.
C. If it is required to perform repairs in “Restricted Area B”, the operator should consult the SRM for specific procedures in related chapters rather than his own solution even though prior Airframe Manufacturer's approval is obtained.
A. The General Aviation Manufacturers Association compiled this specification to guide the manufacturers of the aircraft engine and component developing their Continuous Airworthiness Program Inspection Documents.
B. The Continuous Airworthiness Program Inspection Documents prepared by the manufacturers of the aircraft engine and component was guided by the General Aviation Manufacturers Association.
C. This specification was developed by the General Aviation Manufacturers Association as guidance for airplanes,engine and component manufacturers in preparing Continuing Airworthiness Program Inspection Documents.
A. If the unit is unchanged, it is necessary to monitor the ambient temperature for at least 15 cycles.
B. Keep monitoring the temperature of the unit for a minimum of 15 cycles until you install a new one.
C. If the unit remains unchanged, its temperature should be checked for at least 15 cycles.
A. 如果只能用可能导致单个组件/单元没有超出预测的重大检测程序,而且完成不需要完全的检测,装置或组件移除/组装程序可查阅系统/子系统检测。
B. 如果重大测验程序使用独立的模块/单元来呼叫没有超出范围的部分,且完成不需要整个系统进行测验,单元或模块移除/安装程序只可以按照系统/子系统测验来做。
C. 只有在使用主要测试程序而单个组件/装置测试不重复进行,且完成该过程不要求完成整个系统的测试时,装置或组件的拆/装程序才可参考系统/子系统的测试。
A. Measure the movement of the inboard and outboard flaps.
B. Measure the move for the inboard and outboard flaps.
C. Examine movement of the inboard and outboard flaps.
A. 有24片宽弦钛合金风扇叶片。
B. 有24片宽弦合金钢风扇叶片。
C. 有弦宽为24的钛合金风扇叶片。
A. Give long term protection to areas of bare metal since bare metal surfaces are usually unsatisfactory for an electrical bond.If there is corrosion on the surfaces,it will cause severe problems.
B. Give temper protection to areas of bare metal since bare metal surfaces are always satisfactory for an electrical bond.If there is corrosion on the surfaces,it will cause severe problems.
C. Protect the bare metal areas temporarily since this kind of surfaces are usually adequate for an electrical bond.If corrosion happens on the surfaces,it will bring serious problems.