A、 Check the drain holes for signs of corrosion.
B、 Examine the drain holes for signs of corrosion.
C、 Clean the drain holes for signs of corrosion.
答案：B
A、 Check the drain holes for signs of corrosion.
B、 Examine the drain holes for signs of corrosion.
C、 Clean the drain holes for signs of corrosion.
答案：B
A. This limiting rate-of-climb value shall be distinguished clearly along the chart together with the power and configuration conditions.
B. This limiting rate-of-climb value and the power and configuration conditions shall be identified clearly on the chart.
C. The chart shall clearly show the identity of this limiting rate-of-climb value as well as the power and configuration conditions.
A. CAP检查列出制造商建议的零件或组件的报废时间(使用小时数、循环或其他适当的决定因素)和FAA要求的关于时寿零件或组件的报废(维护拆换)时间。
B. CAP检查设定四家推荐的制造商的零件或组件退役时问(使用时间周期或其他适当的计算方法)和FAA要求的时间限制零组件的退役(维护拆换)时间。
C. CAP检查包在建议的厂家零部件退役时间(使用时间周期或其他合适的计量因子)和FAA要求的零部件退役(不服役)时间后进行。
A. The dictionary includes some unapproved words that can be technical names if you can put them in the applicable technical name category.
B. Some approved words are included in the dictionary, they can be technical names if they belong to applicable technical name category.
C. The dictionary contains some unapproved words, which can be put, in separate technical name category, they can be technical names.
A. Do the leak test of the system.
B. Test the system for leaks.
C. Find the leaks of the sytem.
A. 由于其他维护工作需要对设备进行维修。
B. 由于对设备进行维修需要先完成其他维护工作。
C. 由于完成其他维护工作而需要对设备进行的维修。
A. 确保表显数值与油箱加油量一致。
B. 确保设备测量值与燃油箱的实际油量一致。
C. 确保仪表上的指示与油箱内的油量一致。
A. 建立单独的导线标识码,以组建追踪电路(如图5)
B. 建立单独的导线标识码,以协助追踪电路(如图5)
C. 建立单独的导线标识码,以装配追踪电路(如图5)
A. In this specification, for those who do not have an established code, individual electrical symbols are given as a suggestion.
B. As a suggestion for those who do not have an established code, individual electrical symbols are gained in this specification.
C. As a suggestion for those who do not have an established code, individual electrical symbols are required in this specification.
A. A calculated latitude error usually will occur in one ADIRU. If the position difference is in one ADIRU, start a new alignment . If the new alignment has a position difference, refer to troubleshooting procedures in part two of the maintenance manual.
B. A calculated longitude error usually will occur in one ADIRU. If the position difference is in one ADIRU, restart a new alignment if the new alignment has a position difference, refer to troubleshooting procedures in part two of the maintenance manual.
C. A calculated longitude error usually will occur in one ADIRU if the position difference is in one ADIRU, start anew alignment. If the new alignment has a position difference refer to troubleshooting procedures in part two of the maintenance manual.
A. 使用玻璃纸以防止损坏表面。
B. 使用树脂以防止损坏表面。
C. 使用聚酯纤维以防止损坏表面。
