A、 用黑色字体在页面外侧对改版、补充和删除进行说明,对应于已经更改的部分打印内容。
B、 应在书页外侧以垂直黑线标记修订、增加和删除之处,仅对应于印刷件中已更改的内容。
C、 对于经过修订和增删的文字,沿书页外侧用粗黑直线加以标识,并仅打印修改。内容部分。
答案：B
A、 用黑色字体在页面外侧对改版、补充和删除进行说明,对应于已经更改的部分打印内容。
B、 应在书页外侧以垂直黑线标记修订、增加和删除之处,仅对应于印刷件中已更改的内容。
C、 对于经过修订和增删的文字,沿书页外侧用粗黑直线加以标识,并仅打印修改。内容部分。
答案：B
A. The pointer that moves along the scale is a vertically.
B. The pointer moves horizontally along the scale.
C. The pointer moves vertically along the scale.
A. 如果超过50%的污染物造成孔堵塞,则要清理显示组件背面的孔。
B. 如果污染物造成孔堵塞超过50%,就要清洁显示组件后面的孔。
C. 如果50%的孔被污染物堵塞,则要清理显示组件底部的孔。
A. The fuselage includes skin, stringers, frames, floor beams, floor, tail cone, and fuselage to wing and tail fittings, etc.
B. The fuselage includes skin, frames, stringers, floor beams, floor, tail cone, and fuselage to wing and empennage fillets, etc.
C. The fuselage includes skin, beams, stringers, floor frames, floor tail skid, and fuselage to wing and rear fairings ,etc.
A. For this procedure, make sure that one person is available as backup.
B. Two persons are necessary to do this procedure.
C. Two persons are mandatory to do this procedure.
A. This is the low limit of flight speed at which the airplane can be controlled directionally and laterally.
B. This is the upper limit of flight speed at which the aircraft is directionally and later ally controllable.
C. This is the largest flight speed at which the airplane is directionally and laterally steerable.
A. Put the mark in its correct position with the help of the clamp.
B. The clamp can be used to let you set the mark in its correct position.
C. The mark can be used to let you put the clamp in its right position.
A. 跳开关安装在组件的前部。
B. 跳开关位于组件侧面。
C. 跳开关安装在组件的后部。
A. 对机场设备的持续投资,包括跑到、航站和技术,将确保源于空管系统更换和飞机机队的更新所带来的最大收益。
B. 对机场基础设施的持续投资,包括跑到、航站和技术,将确保源于空管系统更换和飞机机队的管理所带来的最大收益。
C. 机场基础设施的持续投资,包括跑到、航站和技术,将确保源于空管系统更换和飞机机队的更新所带来的最大收益。
A. If the electrolyte leaks, remove it immediately.
B. If the electrolyte spills, remove it immediately.
C. If the material of battery spills, remove it immediately.
A. Drill the hole until it has a radius of 8.00±0.003 mm.
B. Ream the hole until it has a diameter of 8.00±0.003 mm.
C. Trim the hole until it has a width of 8.00±0.003 mm.
