315、为提高滚齿机的传动链精度,在修理时一般不能采用( )。
A. 减少传动元件的数量
B. 提高传动元件的安装精度
C. 装配时用误差补偿
D. 加装误差校正装置
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-5672-c0b1-dce1e9b36800.html
点击查看答案
227、出现三坐标测量机测头()的原因一般为电缆接触不良或测头损坏。( )
A. 移动失灵
B. 回退失败
C. 卡死
D. 不回零位
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-a6ef-c0b1-dce1e9b36800.html
点击查看答案
325、整修大型机床基础时,要在水泥浆( )时,放上调整垫铁,并用水平仪和检验平尺找正垫铁。
A. 刚铺完
B. 未完全干固
C. 完全干固
D. 都可以
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-69fa-c0b1-dce1e9b36800.html
点击查看答案
49、转子的支承刚度包括()。( )
A. 转子刚度
B. 基础刚度
C. 轴承座刚度
D. 油膜刚度
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-0e04-c0b1-dce1e9b36800.html
点击查看答案
99、修磨锯床的锯条前,应让砂轮机空转()min后再修整砂轮,进行锯条的修磨操作。( )
A. 2~3
B. 3~5
C. 5~8
D. 8~10
https://www.shititong.cn/cha-kan/shiti/000e09bc-5528-a2a5-c0b1-dce1e9b36800.html
点击查看答案
167、静平衡是消除零件在()上的偏重。( )
A. 轴向位置
B. 径向位置
C. 旋转中心
D. 周边
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-3112-c0b1-dce1e9b36800.html
点击查看答案
13、提高齿面抗点蚀的方法有哪些()。( )
A. 提高齿面硬度
B. 减小齿面的表面粗糙度值
C. 增大润滑油的黏度
D. 减小润滑油的黏度
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-cb4a-c0b1-dce1e9b36800.html
点击查看答案
28、选择分度头的分度盘时,尽可能选用分数部分分母的()的分度盘孔数,以提高分度的精度。( )
A. 倍数较大
B. 倍数较小
C. 数值相等
D. 成倍数
https://www.shititong.cn/cha-kan/shiti/000e09bc-5528-0dff-c0b1-dce1e9b36800.html
点击查看答案
121、光学分度头的光学刻度盘有较高的测量精度,它固定在()上,能准确地显示零件分度的角度值。( )
A. 蜗轮
B. 蜗杆
C. 读数装置
D. 主轴
https://www.shititong.cn/cha-kan/shiti/000e09bc-5528-d3f9-c0b1-dce1e9b36800.html
点击查看答案
92、()不准在水平或倾斜方向上使用电葫芦。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-cd58-c0b1-dce1e9b36800.html
点击查看答案