65、()严禁使用汽油清洗零件。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-9a7b-c0b1-dce1e9b36800.html
点击查看答案
246、采用()划线时,将大型工件直接安放在坚实水泥地的调整垫铁上进行划线。( )
A. 条形垫铁与平尺调整法
B. 平板接长法
C. 拉线与吊线法
D. 工件位移法
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-cda0-c0b1-dce1e9b36800.html
点击查看答案
36、SY-112钢质修补剂,适用于铸钢件缺陷及钢铁零件磨损、划伤的修复。它的操作工艺是()。( )
A. 表面处理
B. 混料
C. 固化
D. 涂敷
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-f716-c0b1-dce1e9b36800.html
点击查看答案
328、齿侧间隙检验铅线直径不宜超过最小间隙的( )倍。
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-6fcd-c0b1-dce1e9b36800.html
点击查看答案
228、在使用三坐标测量机加长杆时,要选择适当测力的(),尽量减少其疲劳强度,延长使用寿命。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-a8ca-c0b1-dce1e9b36800.html
点击查看答案
241、对于特殊或偏重的大型工件划线,采用3点支承后,在必要的地方增设几处()。( )
A. 补充支点
B. 辅助支点
C. 辅助支承
D. 补充支承
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-c22b-c0b1-dce1e9b36800.html
点击查看答案
158、汽油、酒精等去污、去油能力很强,洗涤效果好,溶液挥发快,适用于()的清洗。( )
A. 金属零件
B. 光学仪器
C. 量具
D. 精密零件
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-1f57-c0b1-dce1e9b36800.html
点击查看答案
56、塞尺不能测量()的工件。( )
A. 温度较高
B. 温度较低
C. 表面粗糙
D. 形状复杂
https://www.shititong.cn/cha-kan/shiti/000e09bc-5528-4a95-c0b1-dce1e9b36800.html
点击查看答案
13、()对于特大型工件、可用拉线与吊线法来划线,它只需经过一次吊装、找正,就能完成工件三个位置的划线工作,避免了多次翻转工件的困难。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-394b-c0b1-dce1e9b36800.html
点击查看答案
117、()齿条齿廓上各点压力角不相等。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-fcb1-c0b1-dce1e9b36800.html
点击查看答案