38、()高精度的轴类零件常采用冷校直来使毛坏的加工余量均匀。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-6675-c0b1-dce1e9b36800.html
点击查看答案
337、当系统中压力不足时,首先要检查压力表是否失灵,如失灵则要( )。
A. 更换压力表
B. 修配活塞
C. 更换密封圈
D. 调整正确
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-8165-c0b1-dce1e9b36800.html
点击查看答案
200、在铲齿车床上铲除的齿背曲线为()。( )
A. 阿基米德螺旋线
B. 抛物线
C. 折线形齿背
D. 中心线
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-71e3-c0b1-dce1e9b36800.html
点击查看答案
179、采用精密圆柱检测法测量标准锥棒时,要将外圆锥体()放在检验平板上。( )
A. 水平
B. 外锥母线
C. 竖立
D. 倾斜
https://www.shititong.cn/cha-kan/shiti/000e09bc-5529-4947-c0b1-dce1e9b36800.html
点击查看答案
7、()对角线法测量矩形工作台平面度误差时,所用桥板中心距长度必须是一样的。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-2e0f-c0b1-dce1e9b36800.html
点击查看答案
107、()磨削强度、硬度较低的材料,应选用较硬的砂轮。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-eaa9-c0b1-dce1e9b36800.html
点击查看答案
304、镀铬工艺中,目前应用最为广泛的镀铬液是以( )作为催化剂的镀铬溶液。镀液中仅含有铬酐和硫酸,成分简单,使用方便。
A. 盐酸根
B. 硝酸根
C. 碳酸根
D. 硫酸根
https://www.shititong.cn/cha-kan/shiti/000e09bc-552a-41c4-c0b1-dce1e9b36800.html
点击查看答案
113、用水平仪进行测量时,要减少()的影响。( )
A. 振动
B. 大气压力
C. 温度变化
D. 湿度变化
https://www.shititong.cn/cha-kan/shiti/000e09bc-5528-c24c-c0b1-dce1e9b36800.html
点击查看答案
46、()在作硬度试验时,相邻两个压痕之间的间隔必需大于压痕直径的3倍以上。( )
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-73c5-c0b1-dce1e9b36800.html
点击查看答案
42、离合器包括有()。( )
A. 十字滑块式
B. 侧齿式
C. 超越式
D. 摩擦式
https://www.shititong.cn/cha-kan/shiti/000e09bc-552b-0148-c0b1-dce1e9b36800.html
点击查看答案