413.汽车槽车装卸现场油汽浓度超标通常使用( )驱散现场的气体。
A. 蒸汽
B. 氮气
C. 柱状消防水
D. 压缩空气
https://www.shititong.cn/cha-kan/shiti/001a5d26-230c-d0b8-c0c5-1e92eb8f1f00.html
点击查看答案
9.不属于减少油品蒸发损耗的措施是( )。
A. 夏季午后对储存轻油的地面金属油罐进行淋水降温
B. 采用密闭装油系统
C. 对罐内油品打循环,使油品温度密度分布均匀
D. 改进油罐结构,提高油罐承压能力
https://www.shititong.cn/cha-kan/shiti/001a5d9a-b510-4201-c0f6-b63fe774ea00.html
点击查看答案
23.某油品在内径为100mm的管线内流量为150m³h,其流速为( )。
A. 5.1
B. 5.3
C. 7.2
D. 7.6
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd5c-8266-c0c5-1e92eb8f1f00.html
点击查看答案
59.每班需对固定式空气泡沫系统管线、阀门巡回检查一次,检查管线、阀门是否正常,发现问题及时汇报处理。( )
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd61-cbe3-c0c5-1e92eb8f1f00.html
点击查看答案
258.离心泵启动前,只要密封腔内充满液体,即可启动。( )
解析:解析:离心泵启动前,应保持密封腔内充满液体,并经盘车后方可启动。
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd63-74f6-c0c5-1e92eb8f1f00.html
点击查看答案
196.便携式氧气检测仪使用简便,只需按下”ON”键,启动检测仪就可以使用。( )
解析:解析:便携式氧气检测仪使用简便,只需按下”ON”键,启动检测仪,放置30秒钟,待其稳定后,方可正常使用。
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd62-f528-c0c5-1e92eb8f1f00.html
点击查看答案
230.更换输油臂旋转接头的副密封圈方法是拆下旋转接头装配螺栓,然后卸下连接法兰,取出主密封圈,向后拉动连锁杆以关紧管接头,即可进行副密封圈的更换。( )
解析:解析:更换输油臂旋转接头的副密封圈方法是拆下旋转接头装配螺栓,然后卸下连接法兰,取出主密封圈,即可进行副密封圈的更换。
https://www.shititong.cn/cha-kan/shiti/001a5d9a-b515-5314-c0f6-b63fe774ea00.html
点击查看答案
122.接到来车装油预告后,应( )。
A. 放下渡梯
B. 通知司泵员开泵
C. 检查渡梯是否收起,扣牢
D. 打开鹤管回流阀
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd5d-5d4b-c0c5-1e92eb8f1f00.html
点击查看答案
135.槽车不需刷洗的标准要求不得有杂物、油泥等,车底残存油宽度不宜超过( )。
A. 10mm
B. 20mm
C. 30mm
D. 40mm
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd5d-7797-c0c5-1e92eb8f1f00.html
点击查看答案
83.槽车对好位后,机车未摘掉挂钩离开油台,可放下渡梯登车。( )
解析:解析:槽车对好位后,机车未摘掉挂钩离开油台,不准放下渡梯登车。
https://www.shititong.cn/cha-kan/shiti/001a5c64-dd61-ff5c-c0c5-1e92eb8f1f00.html
点击查看答案